20 Most Recent Minolta Di2510 All-In-One Laser Printer Questions & Answers


replace the drum and developer clear counters first then run F8 afterward

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Mar 12, 2017


Tryy this site mite have the service manual

Service manuals electronic components datasheets and equipment schematics...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Nov 22, 2015


Open the right side then open the hot part (The fuser located above the drum cartridge with a flash lite look at the to rollers is ther a line on one of them BE CAREFUL VERY VERY HOT if on. IF so replace the fuser try this site

Precision Roller Printer Toner Cartridges Parts and Supplies Office...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Nov 21, 2015


First open the right side cover where the image unit is located. Check the two latches that latch the door ensure they are not broken, especially the rear one. Then get a paper clip and stick the clip in the small hole on the right side of the control panel it will touch a switch. The control panel will go thru some screens when you see the screen with the copiers on it on the left side of the screen in the middle you will see a small "." When the dot appears touch 3 button. Then the machine will continue to the code screen. Press the Utility button you should see a new button "Maintenance Mode" touch it then touch trouble reset. The machine will again go thru screens will see the"." again do nothing. Should go ready to Copy. If the code comes back do not reset you are messing with the Fuser the Hot part. Continuing to reset without a technician looking at and or replacing it, the fuser can catch on fire and that would ruin a perfectly good day.


Try this site for parts
Precision Roller Printer Toner Cartridges Parts and Supplies Office...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Nov 21, 2015


AT best would be XP or 95. Di250 is a legacy. try this site Self Help Product Support Konica Minolta Business Solutions Inc

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Nov 21, 2015


Have you had the developer and drum replaced or does the screen say Replace PC Drum? There are certain house chores the copier does before "Ready to Copy" it is waiting for them to get done, so that equals "Please Wait". One big item is making sure the developer and toner are properly mixed inside the image unit underneath the drum. Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure and make sure the counters where cleared. Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer, FIRST. IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developer and a new drum and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you will start all over again with new developer and a new drum.

Also try removing the toner bottle, turn off the machine with the toner bottle out and cover closed turn on the machine when it ask for toner properly place the toner bottle in the machine

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Nov 19, 2015


ABORT CODE check all connections between circuit board check each connector one at a time check for a bend pin, worse case change out boards

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 22, 2015


So you replace the fuse ? on the image unit. what do you mean by CCUT??? YOU CUT THE FUSE when the image unit is replaced a new fuse must go in so the copier will blow it to know it got a new image unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 22, 2015


Rollers need to be cleaned use one of the regular paper draws instead. What type of media are you trying to run through the bypass tray media=paper

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 22, 2015


Check the power supplies. check power cord plugged in properly to the machine snug and tight recommend a tech from Konica Minolta

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 21, 2015


sir, Have you had the developer and drum replaced or does the screen say Replace PC Drum? There are certain house chores the copier does before "Ready to Copy" it is waiting for them to get done equals "Please Wait". One big item is making sure the developer and toner are properly mixed inside the image unit underneath the drum. Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure and make sure the counters where cleared Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer. IF not then the copier thinks the new drum and new developer are old. Copier works on the counters that how it know it got a new drum and developer. Get new develop and new drum and have it installed correctly, Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE AVACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you start over with new developer and new drum

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 20, 2015


Mam/sir First check the right side cover where the image unit is located. Check the two latches that latch the door. Are they broken especially the rear one. Then get a paper clip and stick the clip in the small hole on the right side of the control panel it will touch a switch. The control panel will go thru some screens when you see the screen with copiers on it on the left side of the screen in the middle you will see a small "." when the dot appears touch the 3 button. Then the machine will continue to the code screen. Press the utility button should see a new button "Maintenance Mode" touch it then touch trouble reset. The machine will again go thru screens will see the"." again do nothing. Should go ready to Copy. If the code comes back do not reset you are messing with the Fuser the Hot part continue reset without a technician looking at and or replacing it can catch on fire that would ruin a perfectly good day

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 17, 2015


Can not use windows 7 on that machine legacy Minolta best is xp,2000 or 95 Self Help Product Support Konica Minolta Business Solutions Inc try this

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 17, 2015


See the last post on this issue.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 15, 2015


Has the drum been replaced? IF not then recommend that the counter not be reset because the copier use the counters to determine voltages for certain assy. like drum and developer unit, so if you reset the counters with out replacing the parts the machine will give codes and provide bad copy quality issues. Reset code is the only way the machine knows it got new parts

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 15, 2015


Sir/Mam did you mean C-13D0 because could not fine the C13C0 in the service manual.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Feb 07, 2015


GO to konicaminolta web site. I believe that the best that machine can use is xp but check it any way.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta Di2510... | Answered on Jan 10, 2015

Not finding what you are looking for?
Minolta Di2510 All-In-One Laser Printer Logo

35 questions posted

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1316 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Ed
Ed

Level 3 Expert

473 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Minolta Office Equipment & Supplies

  • Minolta Office Equipment & Supplies

Most Popular Question

minolta di 2510 code c0500

  • Office Equipment & Supplies
Loading...