20 Most Recent
Questions & Answers
How do i go about transfering vhs-c video from an
You have several options. But important one to understand is the limitations of a PIII computer like Armada e500. You may not have enough grunt to convert stuff, even after buying the necessary video capture devices which work on USB.
Also I am assuming you either have the jvc camcorder still available or atleast have a VHS-C to VHS adapter to play the tapes on a standard VHS tape player.
Unless you are having a lot tapes and need editing while converting, your better bet might be to go to one of the shops that convert these tapes on to DVD or a suitable flash drive which might work out cheaper and quicker.
The last time I did this thing (quality of my VHS-C tapes was bad) I bought a Samsung combined VHS Video / DVD recorder and used the dubbing feature to burn DVDs. Cost me about $150 a year ago. I was able to do some editing on the way as I was connected to the TV screen as well. Saved me the hassles of dealling with the PC type video capture devices and software.
JVC S-VHS Tapes...
on Dec 25, 2009
How tosave image to my facebook
Allyou need is to check on your home page to save the images/photographs in the right hand side. Click and open the page, then open and browse from your picture folder or file , click and upload.
All you need is to just follow the window logically and upload the image to the facebook list. you can reset the privacy accordingly for private or public viewing.
on Dec 09, 2011
My CA-DXT99 jvc component appears tray error
The fault could be the wrong alingment or the failure or displacement of the mode switch or sensors int he tray settings. If the trays set bacl after few times then you will have to check for dirr tin sensors or failure of the optocoupler sensors. However if the tay never sets right, then the mechanism has a wrong mode settting which might have happened as it jumped over.You will have to take the entire tray mechansim and set them. However this is quite tricky and you will have to set from the begining of the resting of the tray to the noemal setting of the cd drive mechanism. If you have not attempted this sor tof job I would not advice you as the logic settings of the tray must be thought of. However if you can try set the tray and use the load motor drive to trun externall and see that the mechanism works from the outside. If so set it back to the circuit and test. Please see if any tray has been damaged and will result in the same fault.Hope you do this right. Good day
on Jul 26, 2010
I DONT HAVE INSTRUCTIONS FOR A JVC VCR HR-7665EA
This manual is no longer available as it is quite an old VCR unit. It is no longer listed in the general database. JVC maintain a number of archived manuals at this link
You can browse the archived models to find one that is nearest your model and the general instructions for use will be the same. Alternatively if you contact JVC support from that link they will often oblige by emailing you the manual for your model from the non published archive that they maintain.
Hope this helps. Please remember to rate my answer. Many Thanks.
on Jul 29, 2009
How to repair Motorolla Talkabout 250 antenna
I have just repaired four of these radios, with complete success.
You need a tube of black Stixall (currently £5.81 from Tool Station), a skeleton gun and a saucer of water with a good squirt of washing up liquid.
Take the back off the radio, take out the batteries and remove the rear cover by undoing the retaining screws using a screwdriver with a star shaped bit. Unscrew the circuit board now exposed using the same screwdriver bit. Remove the damaged rubber aerial with coiled copper core, being careful not to damage or distort the copper core. It lifts off one of the screw lugs revealed when removing the circuit board. Get rid of all of the old rubber.
Now put the end of the copper coil back over the lug (where it came from) and screw the PCB back on followed by the back of the unit.
Now form a new rubber cover to the copper aerial using Stixall, squirted into place. Squirt it down into the aerial housing so that it will get mechanical purchase from the body of the radio. Put on plenty, completely coating the copper aerial. Now dip your fingers in the saucer so that they don't bond to the Stixall and mold it into a smooth aerial shape. Leave it to cure for 24 hrs and then dust it with flour. Job done.
I have tested my repaired radios and they are great, the new "aerials" have lasted well. I am especially pleased that I don't have to throw them away.
Good luck - regards SJP
18 hours ago | Electronics - Others
Not finding what you are looking for?