20 Most Recent Toshiba 36A50 36" TV - Page 3 Questions & Answers


This is an easy repair if you've ever soldered and would not be too costly for a repair shop to do it for you. The problem is a bad Vertical Output IC (usually mounted on an aluminum heat sink with the part on it labeled LA78?? ) and 1 or 2 bad capacitors. Some times you can even fix the problem by re-soldering the contacts of the IC- To find the IC follow the 4 wires that come from the Yoke (which is a contained coil of wires slipped over the neck of the picture tube(s)) back to the board. 2 of the wires go to the horizontal o/p and 2 to the Vertical o/p the thinner gauge wires are for the vertical.

Toshiba 36A50... | Answered on Sep 28, 2009


You had parts in the vertical deflection circuit failing, most common are the vertical output IC and possibly several capacitors also in the same circuit.

Toshiba 36A50... | Answered on Sep 12, 2009


I have same issue changed the HDMI cable and it get fixed

Toshiba 36A50... | Answered on Sep 11, 2009


Yes,not more than $150 dollars ok,not worth repairing CRT tube tv more than that.Take to the shop get the estemate.

Toshiba 36A50... | Answered on Sep 07, 2009


i dont think so
how the lines are?
horizontal or vertical?

Toshiba 36A50... | Answered on Jul 29, 2009


yo pandac is it a universal remote?

Toshiba 36A50... | Answered on Jun 25, 2009


Some el.components are loose on tv circuit board.I have removed the back cover,supported tv picture tube 45 deg.against wall.This tv is heavy!One screw on left holds the circuit board to bottom case.Removed and supported this board on few heavy books.Turned tv on and gently probed all the componets on top of the board with plastic drinking straw.In my case transistors Q-830 and Q-421 needed resolder loose joints.These components are mounted on flat aluminium heat sink strips located sligtly left of center of the circuit board.Also blobed bit of silicone into base hole and foot of alu.heat sink to support it.

Toshiba 36A50... | Answered on May 14, 2009


My Toshiba 36A50 had the same issue. The picture would gradually shrink until it no longer appeared and there was only a thin line running from left-to-right across the center of the screen. The volume still worked perfect.

From information I gleaned from this site and others, I removed the main circuit board and flipped it over to re-solder the pins going to the Vertical IC (TA8427K). This IC is right about center of the board mounted on an aluminum heatsink so it is soldered in vertically. You can easily see the part number on the IC and it is the only one of that part number. Additionally, the silk-screen on the PC board has a QC301 next to it identifying the part.

After I re-soldered it, the TV works excellent. I just did this yesterday afternoon 10.26.08.

Thinks to note that have been pointed out by others:

  1. There is high voltage in the TV even after the power is removed. There are several sites where they tell you how to remove the power.
  2. Make a note of all connections. Most of the connectors are keyed to go in only one way but some you can turn the connector either way. Write down all the information and take some digital pictures before you disconnect everything.
  3. As was pointed out but other people, the Vertical IC and/or some of the surrounding capacitors may be defective and need replacement. Its possible that your local Radio Shack may have what you need but I would not count on it. A possible source for parts is www.digikey.com.

Toshiba 36A50... | Answered on May 06, 2009


same problem for me too - just a red light showing and nothing else.. sometimes it works but only about 1 in 100 :(

Toshiba 36A50... | Answered on May 03, 2009


find your remote instuctions and it will say in them. dont follow the tv stuff.

Toshiba 36A50... | Answered on Apr 30, 2009


Sounds like vertical deflection circuit problem. Could be as simple as a bad solder joint around a heavy component such as a transformer, a bad capacitor, overheated resistor, bad IC or transistor, or combination of these. Repair would require knowledge and experience.

Toshiba 36A50... | Answered on Apr 15, 2009


You need to be using the TV's remote, not the Time Warner remote.  You are reading the TV's manual to set it's remote, not the Time Warner remote.  If you want the Time Warner remote to operate the TV, you will need to find the instructions that the Time Warner box/receiver provides and enter the TV's code.

Toshiba 36A50... | Answered on Mar 24, 2009


vertical section is failing probably a bad ic or open resistor

Toshiba 36A50... | Answered on Mar 20, 2009


you could read the oweners manual it will tell you how to do this. Go in the menu and find auto search then hit search or ok or what ever it tells u to do.

Toshiba 36A50... | Answered on Mar 05, 2009


If flexing the board will "fix" the problem, then the most likely issue is poor solder connections on that board. Look for any connections that appear grainy or have rings and resolder them. The IC involved here is the vertical IC which will be a small flat IC attached to a heatsink. It may be marked LA7837 or something similar and have about 9-11 pins.

Try the resoldering and update this with your results.

Dan

Toshiba 36A50... | Answered on Mar 04, 2009


need to turn off close captson off hope i speled that right.

Toshiba 36A50... | Answered on Feb 28, 2009


This is usually due to bad solder connections to the vertical output integrated circuit. Because the part gets pretty hot during operation, the connections can degrade over time and cause the loss of picture. The solution is to resolder those connections. It's an easy job if you have some experience with electronic soldering. The hardest part, especially in a big set like yours, is getting the circuit board out and flipped over to access the solder side. Also, some parts in a TV can store possibly lethal charges even after it's been off for a while.

If you want to try it yourself, the output IC is mounted on a metal heatsink near the middle of the circuit board. I haven't faced one of these in a while but I think the part location marked on the board for this is IC401. Resolder the connections to the pins of this part and it should restore your picture.

If you have some doubts about trying this yourself, you might consider calling a servicer in your area and get an estimate for a repair call. The shop I used to work for charged around $90 for this kind of job, including the trip charge, but this is a number of years ago.

Toshiba 36A50... | Answered on Feb 11, 2009


skate,

are you reffering to a game console connecting direct to a TV screen?

1st try to check if your TV screen have a terminal jack indicating "A/V INPUT" A/V stands for Audio/video. if the screen doesn't have this, you'll be needing A/V to RF converter

2nd if your screen does have a terminal jack indicating A/V INPUT the next step you need to do is: check your game consul cable it should have a 3 RCA cable having RED/WHITE and yellow marking.

RED and WHITE cable marking stands for "AUDIO"
YELLOW cable marking stannds for "VIDEO"

connect this cable to A/V input of your screen following the color code ( yellow to yello/ red to red/ white to white) then from the screen press a button indicating "A/V" or "INPUT"

cheers,
mark

Toshiba 36A50... | Answered on Jan 29, 2009

Not finding what you are looking for?
Toshiba 36A50 36" TV Logo

104 questions posted

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76099 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Toshiba Televison & Video

  • Toshiba Televison & Video

Most Popular Question

toshiba 36a50 picture thin white line

  • Televison & Video
Loading...