20 Most Recent NetGear RangeMax WPN824 Router Questions & Answers


Wow ... I teach a whole college semester on this. This forum can't possibly provide enough complete information on design, setup, maintenance, security, etc.

View this netgear link:
http://www.netgear.com/Products/RoutersandGateways/RangeMaxWirelessNRoutersandGateways/DG834N.aspx
It includes diagrams...
Go to a book store and purchase a paperback book on home network setup.

NetGear RangeMax... | Answered on Feb 01, 2019


Restart the modem and router and you should be connected.

NetGear RangeMax... | Answered on Feb 05, 2018


Sounds like you[ve already found the solution. The sledgehammer combined with going out to buy a new router (anything but Netgear) should do the trick. It's much better than spending countless hours on the phone with a tech from India who doesn't know shit and only asks questions that they are reading from a transcript. Their customer service is shit and so are their products.

NetGear RangeMax... | Answered on Apr 21, 2017


If your routers are more than three years old, it's time to replace them. I had one 4 years ago, and it was on all the time. It finally died after 2 years. It acted pretty much the same as yours do now. Time to upgrade!

NetGear RangeMax... | Answered on Dec 20, 2016


Netgear is not a browser. It is a Router. For the sake of this question I would assume you were talking about the Router, what do you mean by "Lock"? You can change the default password, and no one will be able to access it. If you only want specific devices to connect to the router, you can:
1) Enable MAC Filtering
2) Disable DHCP, and assign Static IP addresses to the devices
3) Hide SSID (Not Broadcast it)

NetGear RangeMax... | Answered on Mar 04, 2015


You need to access router's interface. You can do so by typing routerlogin.net or 192.168.0.1. Once you're able to access interface you can change channels or set to auto.

NetGear RangeMax... | Answered on Sep 13, 2014


It should be on the label on the bottom or side.

NetGear RangeMax... | Answered on Sep 13, 2014


No. Most ISPs require a modem for modulation and demodulation. Sometimes a DSL model will have both, but this is not your case.

NetGear RangeMax... | Answered on May 23, 2014


Generally it is ADMIN and PASSWORD unless it has been changed then all you would need to do is do a hard reset.Hard reset is performed by holding the reset button for 15 sec while plugged in ,remove power cord then plug in power cord again.Just remember 15 sec. for each without removing you finger from the reset button.

NetGear RangeMax... | Answered on Apr 18, 2014


Comment box should be below your question

NetGear RangeMax... | Answered on Apr 18, 2014


Well this product DGN1000 is a generic router supplied by Netgear and can be used with any ADSL/DSL ISP. Please ensure that you upload the latest firmware for this router from the netgear support site and then you can use it with other ADSL/DSL ISP.
Hope this allows you to resolve the issue. If you need further assistance then let me know.
Regards
Anand

NetGear RangeMax... | Answered on Dec 09, 2013


1) sometimes just delete network info from panasonic then put it back in
2) sometimes change security type in router (login and change from wpa whatever to WEP and see if it likes a simpler less secure security type better.
3) maybe it just isn't getting good signal inside that entertainment center... wireless doesn't pass through stuff very well.

NetGear RangeMax... | Answered on Nov 22, 2013


No you cannot.
To make your printer a network printer you need to connect your printer to a network print server and the connect the print server to the Netgear using a LAN cable.

NetGear RangeMax... | Answered on Feb 15, 2013


Try to update the firmware of your router.

NetGear RangeMax... | Answered on Feb 03, 2013


You can reset your Netgear router/wireless wpn824 router to the factory settings from within the router manager. The reset procedure removes all user-configured settings and returns the router to the original factory settings.

For this reason, only reset the router if you encounter problems that can't be solved with other methods.

Step 1: Check that your Netgear router/wireless wpn824 router is properly connected with your system or not. If it is OK, then press reset button on Netgear router for at least 10 seconds. The 'test' light should flash during this process.

Step 2: Now open browser and enter Netgear's IP address into the address bar. Generally, '192.168.0.1' is the Netgear router IP address but you can find specific IP address in Netgear wpn824 router manual.

Step 3: Now enter your default username and password to log in to router.

Step 4: Click 'Erase' button under the 'Revert to Factory Default Settings'. This process will erase all your previous changes that have been made to the router and restore the configuration settings to factory setting. Don't interrupt the process until the process is finished.

Once the router's 'test' light has stopped blinking and the configuration page you are on has refreshed, the wpn824 router has been reset.

Feel free to get instant online Netgear router
support at http://www.vtechsquad.com/netgear-router-support/ to fix Netgear router/wireless router issues.

NetGear RangeMax... | Answered on Oct 12, 2012


  • open Command Prompt, type 'ipconfig/all' and hit Enter. Check Default Gateway, it should be 192.168.1.1, your Netgear device's IP address.

  • If you are still unable to browse the Internet, ping your router's connection to the PC. Open Command Prompt, type 'ping 192.168.1.1', hit Enter. If your PC is receiving connection from your Netgear device, you will see a message like Reply from 192.168.1.1: bytes etc. If there is no connection, you may see the Request timed out message.

  • The Request timed out error can occur due to two things: (1). incorrect physical connection between your Netgear device and the PC or (2) incorrect wireless network setup & configuration. Recheck and correct the Ethernet connection between your PC and the Netgear device. Also reinstall the TCP/IP stack and update Netgear device driver software.

  • When done, check back if you can browse the Internet or not. If the problem persists, hard reset your Netgear wireless router

If you need any kind of technical assistance you can contact support cell at -http://vtechsquad.com/netgear-router-support/

NetGear RangeMax... | Answered on Sep 03, 2012


A forgotten or lost router password cannot be recovered. It can only be reset by hard resetting the router. ....read more to reset password

NetGear RangeMax... | Answered on Aug 31, 2012


Have you made any changes to the router? Blocked or port forwarded port 80.

NetGear RangeMax... | Answered on May 31, 2012

Not finding what you are looking for?
NetGear RangeMax WPN824 Router Logo

343 questions posted

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

NetGear Computers & Internet

  • NetGear Computers & Internet

Most Popular Question

netgear range max built in modem

  • Computers & Internet
Loading...