20 Most Recent Zebra 170XiIIIPlus Thermal Label Printer Questions & Answers


i would open the back panel after removing power cord and check to make sure all the connectors inside are firmly seated.

Zebra... | Answered on Aug 31, 2017


Simply press the PAUSE button then press CANCEL. If you have sent a batch of 500 labels, though, you will have to press CANCEL 500 times. I usually just turn the printer off, cancel the job in the printer driver status box, then wait for all of the error messages to pop up.

Zebra... | Answered on Mar 02, 2016


The DC power supply drives that motor and may start running it backwards when it begins to fail. The motor normally makes more noise than usual in both directions when it starts to fail like this.

Google "43470-002 power supply, Xi III +" and you will be able to purchase the part.

Zebra... | Answered on Apr 03, 2015


I believe you should check the website and download the manual and go over. I think you will find it useful.http://www.zebra.com/id/zebra/na/en/index/products/printers/high_performance/170xiiiiplus.html

Zebra... | Answered on Jun 21, 2014


you possible can with software, (easylabel or Bartender)

Zebra... | Answered on Jun 01, 2014


Easy, your print job has PR (Print Rate) code set on the zpl code in the job file sent.

remove the PR code and you are done!

Zebra... | Answered on Oct 21, 2013


Have you tried a full media calibration from the menu (removing 8" of label from the backing)? Also if a label has left any pieces behind on the rollers, strike plate, etc it can cause this problem. I use a solvent like Goo Gone to make it clean, but be careful not to wipe the sensors with it. Also I have seen this when my users miss a roller when loading the ribbon. Make it clean, load it carefully and usually it works.

Zebra... | Answered on Oct 12, 2012


Make sure you are using the correct driver 170xiIII plus, and make sure the dpi of the driver matches the print head resolution.203 or 300dpi.

Zebra... | Answered on Sep 23, 2011


Do a calibrate on the panel. you have change your label length

Zebra... | Answered on Sep 16, 2011


You should be able to get to the setting by pressing the SETUP key and then press NEXT until you see a setting called IP RESOLUTION. Use the black oval keys to select Dynamic,Permanent. The default password is 1234. Use the left black oval key to change number position and the right one to change the number value to set the password, then press NEXT. Press NEXT until you get to IP ADDRESS. Again, use the left black oval key to change number position and the right one to change the number value until you get the desired IP address. Press SETUP again and then press SAVE to make a permanent save.

This assumes that you have an internal ethernet card installed.

Hope that helps.

Zebra... | Answered on Aug 14, 2011


Access the printers web page. (- Type its ip address into a computer that can route to it.)

It is on the bottom of the View Printer Configuration Page

Zebra... | Answered on Apr 01, 2011


Make sure the pause light is on and press calibrate. See if this calibration solves the problem. If not align the media sensors (top and bottom) to a position that is aligned with the least amount of preprinted data and calibrate again. Print configuration Power on while holding cancel key for 10 seconds. Use the config to help troubleshoot. Make sure the sensor type matches the media. Download user manual at zebra.com.

Zebra... | Answered on Nov 21, 2010


press PAUSE and CANCEL to reset the printer. turn off and on again.

Zebra... | Answered on Nov 15, 2010


try to go to the driver and go to Advance Setup, here you can rotate or reverse the image.

Zebra... | Answered on Nov 13, 2010

Not finding what you are looking for?
Zebra 170XiIIIPlus Thermal Label Printer Logo

Popular Tags

42 questions posted

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

Gateway information...

Level 2 Expert

252 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Zebra Office Equipment & Supplies

  • Zebra Office Equipment & Supplies

Most Popular Question

zebra 170xiiii feed motor runs both

  • Office Equipment & Supplies
Loading...