20 Most Recent NetGear N600 Wireless Dual Band Router - Page 9 Questions & Answers

is that a question or stinking sPAM.?
I sure can not tell.? this is spam H3LL here, so...

try using English.\?

how to find?

what is xyx?

or learn to google, bingo.

NetGear... | Answered on Jul 21, 2019

Cordless phones, microwave ovens and wireless surveillance cameras between the modem and the device will do it. If it's hard wired to the computer, the signal strength from the phone company may be low. Call the phone company to have them come out and test the signal level that is applied to the modem.

NetGear... | Answered on Jul 07, 2019

You can order an adapter that plugs into the wall socket at the router and at the computer. The direct connect to the router and the network adapter in the computer assures a good connection. Of course, a laptop that you move around with couldn't use this as effectively.

NetGear... | Answered on Jun 29, 2019

http://www.downloads.netgear.com/files/GDC/WGR614V7/wgr614v7_setup_manual_21apr06.pdf hope this helps, but I doubt it will be compatible with new standards

NetGear... | Answered on May 01, 2019


NetGear... | Answered on Apr 09, 2019

There are lots of reasons to facing No internet issues.
Follow below steps to fix issue-
  • Check cable connection are not loose, or damage.
  • Make sure your firmware is updated
  • Soft reset
  • Hard reset

NetGear... | Answered on Feb 07, 2019

there might be a setting in the digiland dl 9002 to forget wi fi connection in the wi fi list of possible wi fi networks.

or reset the unit
they apparently have a small hole that you put a paper clip into and push hidden button to reset the tablets settings to factory default.
With tablet back camera facing you there should be a hole at left bottom corner of back of tablet .
Press and hold this in with the paper clip or a tooth pick
unit should power down
then press power button to power back up
it should be reset to factory defaults

NetGear... | Answered on Jan 08, 2019

If that model is similar to their other routers, then there is a drop-down box in the top right corner after you login, where you can pick the language. Mine was set to "Auto" by default.
netgear language-xpnqcryvoxbslrst3kzoppjq-5-0.jpg

NetGear... | Answered on Jan 06, 2019

It sounds like it's not configured to be a DHCP server. It should be a setting you can turn on. Login to the router. You may need to manually set your computer's IP to be in the same subnet as the router so that you can do so. The default address for the Netgear 7550 would be, so you'll have to set your computer's IP to something like, and then browse to the above address. Username and password are both "admin". If that IP doesn't work, try setting your computer's IP to, and browse to, then look for a "DHCP Server" setting in the Local Area Network section, and make sure it's checked.

NetGear... | Answered on Jan 06, 2019

If you've forgotten the password to your Netgear router, then you're locked out from making any changes. The only way to recover a Netgear router password is to reset the device to factory default settings. You can then set a new password and recover your ability to configure the router.

Other People Are Reading

"" frameborder="0" marginwidth="0" marginheight="0" scrolling="no" style="border: 0px currentColor; border-image: none; vertical-align: bottom;"> 22Instructions
    • 1 Use a pen or paper clip to press the reset button on the back of the Netgear router. Keep the button pressed until the lights in the front of the router start flashing. The router will reboot after resetting itself.
    • 2 Open a browser window and enter the IP address of the Netgear router to access the configuration console. The Netgear default IP address is
    • 3 Enter the default username and password, as follows:
      username: admin
      password: 1234 or password
    • 4 If you are still unable to log in, the router may not have been reset. Unplug the router and hold the reset button for 20 seconds before plugging in the power cord. Repeat Steps 2 and 3 to gain access to the route

NetGear... | Answered on Dec 29, 2018

You didn't supply the Model of NetGear device. Push and hold the reset button for 30 seconds or so, release. This will reset to default settings. Reconfigure the SSID and Security settings. This will help: http://kb.netgear.com/app/answers/detail/a_id/119/~/configuring-your-netgear-router-for-cable-internet-connection

NetGear... | Answered on Dec 29, 2018

Whether you bought a used Netgear router or just forgot your own password, you can reset it and start over.

This is not an unusual problem, so Netgear has made resetting and restarting their routers a simple task

Connect all of your devices.
If your Netgear router is not already connected, it should be plugged in, with one Ethernet cable connecting it to your computer and a second Ethernet cable connecting it to your computer's modem.

Locate the reset button on the rear of your Netgear router.
The reset button is a small inset button and requires a pointed object to reach it.

Use a fine-tipped pen to hold the button down for at least 10 seconds.
The test light should flash during this process.

Open your Internet browser and enter the Netgear router's IP address into the address bar to access the router's information. Generally, Netgear routers use the IP address, but the specific IP address will be listed in the router's manual.

Attempt to log in to the router with the default username and password.
The default username is "admin" and the default password is "password."

If the router's username and password were not cleared away, unplug the router and try holding down the reset button.

While you are holding down the reset button, plug the router back in.
Log in to the router using the default "admin" username and "password" as the password.

You can now reset your information, rename your router and enter your own username and password.


NetGear... | Answered on Dec 29, 2018

We can provide you with precise assistance regarding netgear router issues. You can also get the support form experts but there, you will have to search for the resolution yourself. By calling us, you don't have to do anything, as we will take care of each and everything. Call us today at our toll-free number 1-833-455-2100


NetGear... | Answered on Dec 29, 2018

You may reset router to factory setting from the reset button on the back side of the router. Use a paper pin to press the button for few seconds, the lights on the front would blink and the router would restart with factory setting. Please not that ALL SETTING WOULD BE LOST...AND YOU WOULD HAVE TO MAKE CONFIGURATIONS AND SETTING ALL OVER AGAIN

HOPE IT HELPS...Let me know if you need any further assistance

NetGear... | Answered on Dec 29, 2018

Reset means that you will restore it to factory defaults which will delete all of the configuration settings of the router and will leave you not connecting to internet and wireless as well, but if you really want to reset it, just simply press the black button at the bottom of the N-150 router, press and hold it for at least 15 seconds. Once the lights on the router starts blinking, that means that it is successfully restored to factory defaults.

NetGear... | Answered on Dec 29, 2018

You don't need to do anything to your Wifi just insert the SIM and try to brows over the data

NetGear... | Answered on Dec 20, 2018

Not finding what you are looking for?
NetGear N600 Wireless Dual Band Router Logo

69 questions posted

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers


Level 3 Expert

13434 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

NetGear Computers & Internet

  • NetGear Computers & Internet

Most Popular Question

need reset password factory settings

  • Computers & Internet