20 Most Recent Icom IC-M36 VHF Marine Radio Questions & Answers


Check PTT switch is working? if working then check power output of your radio. if no power then change PA.

Icom IC-M36 VHF... | Answered on Jul 11, 2016


I would recommend cleaning the contacts on the battery AND on the radio. Scrub the contacts with Contact cleaner in can, or denatured alcohol, or a soft pencil eraser. All work pretty well seperately. Just depends on what you have available.

Icom IC-M36 VHF... | Answered on Jul 11, 2014


Take it to a marine radio service center. Double check the connections, typically when the display blinks on such radios, either it's lost programming or it's misconnected.

Icom IC-M36 VHF... | Answered on Nov 05, 2013


Contact ICOM service at www.icom.com, or take it to a marine radio service center.

Icom IC-M36 VHF... | Answered on Nov 05, 2013


Contact the Icom service center. Their main web-page is www.icom.com. From there you can select your geographic area and service (commercial, marine, amateur, etc).

Icom IC-M36 VHF... | Answered on Nov 05, 2013


You may have the CTCSS tone squelch enabled so unless a station you're listening to is encoding CTCSS tones, you won't hear the traffic you're expecting.

Icom IC-M36 VHF... | Answered on Nov 05, 2013


http://www.icom.co.jp/world/support/download/manual/

Icom Radio... | Answered on Oct 10, 2019


You need to be a very good technical person with electronics to work on these. The issue is most likely a PLL board issue. You need to be able to troubleshoot to the component level. The service manual appears to be https://www.manualslib.com/manual/738448/Icom-Ic-706mkiig.html

Icom Radio... | Answered on Oct 09, 2019


it is available on web sight..download it.

Icom Radio... | Answered on May 21, 2019


Contact Icom directly to inquire.

Icom Radio... | Answered on May 20, 2019


Contact iCOM directly to inquire.

Icom Radio... | Answered on May 17, 2019


Sure sounds like a "low volts" reboot due to high current draw.
Are you measuring voltage at the radio itself, after any connector, fuse or circuit breaker? The voltage (at the set) should be slightly different between low and medium power tx. Use a good meter to confirm this. Is the power supply able to supply the current required at high tx power? Is a current limiter operating? A lead-acid battery in parallel with the PSU might be needed at high power.
At high power setting the radio will probably reset faster than a low power input voltage can be measured with a normal meter, so an oscilloscope might be needed to see the power input voltage as it happens (might be very brief).
Could RF be getting back into the power supply? Does it happen on both bands? Is the SWR good? Is the earth good? How long and how thick are the power wires? Is there any filter on the power supply wires (close to the radio)? If it's new there will be a warranty if it's a fault in the unit. Good luck :)

Icom Radio... | Answered on Apr 28, 2019


Que es el error? Aye un numero? Diga mas acerca de este problema.

Icom Radio... | Answered on Apr 08, 2019


YOU CAN NOT THAT IS ONLY DONE BY SERVICE PROVIDERS

Icom Radio... | Answered on Mar 25, 2019

Not finding what you are looking for?
Icom IC-M36 VHF Marine Radio Logo

7 questions posted

Ask a Question

Usually answered in minutes!

Top Icom Radio Communications Experts

Perry Mellott
Perry Mellott

Level 2 Expert

147 Answers

Robert McClure

Level 2 Expert

161 Answers

Vincent G
Vincent G

Level 3 Expert

2361 Answers

Are you an Icom Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Icom Radio Communications

  • Icom Radio Communications

Most Popular Question

ic 36 wont transmit

  • Radio Communications
Loading...