20 Most Recent Konica Minolta Bizhub C652 Color&b/w Copier/printer/scanner/fax Network,finisher Questions & Answers


What is the service code being displayed????

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 18, 2018


no such code for that machine

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on May 14, 2017


its important to find out whether the \'lines\' are in scan direction/ or only through Radf or only from scan glass,

if the lines are only showing when documents are fed throught the Radf, then the problem lies with the document scan plate( left of the main glass platen (about 2" in width)) or with the scan plate blade cleaner

if the lines ONLY appear when copying from the Glass then the issue lies within the optics (probably nothing more than a clean will be needed)

another question would be to ask if the lines are solid (black line overprinting image) or if they are \'missing\' lines where the image has failed to copy, sometimes it can be hard to work out which side the fault lies,so try shaded greys as a copy original .

if the scan lines are appearing on both Radf and Glassplatten ,mode then the issue may be dirty optics/ccd sensor or it could e an indication of the ccd failing or image control pwb in error while interpreting the image file.

what to do

1) place a grey sheet of paper in the Radf and have the copier photocopy both sides of the original and print to single sided sheets ( so the printer turns the original over to complete the task)

observe the result.

2) have the copier photocopy directly from the platten glass- single sided.

observe the result.

ckeck to see if the error has appeared on both sets of prints ,

if the error has only appeared in the first set of prints then the issue may be a tiny DOT on the slit glass (left of platten) - a dot on this glass will indeed appear as a Line as the original is scanned across the glass.

hhope thhis helps

Konica Minolta... | Answered on Feb 19, 2014


Push down Stop buttom and switch on.

Konica Minolta... | Answered Yesterday


The amount of toner in the developer is too high.

service mode.
adjust
tcr
+10

Konica Minolta... | Answered Yesterday


1.The terminal for the first transfer pressure/release sensor is not connected properly.
Reconnect the terminal.
2.Failed PS15 (p/n 08AA 8551 2).
Test photosensor, PS15, in the I/O State Confirmation Mode, 48-0HIGH = home position or LOW = Other than home position by activating M19 (p/n 08AA
8003 0) transfer pressure/release motor, 48-0, 48-1, 48-2, or 48-3. Replace thephotosensor or motor as needed.
3. Possiblefailed Transfer/Pressure Release motor (M19).
Check the operation of the motor(p/n 08AA 8003 0) in the I/O State confirmation mode for proper operation with code 48-0; this should rotate the motor
constantly. Replace motorif needed.
Also check for possibleopen ICP fuses, ICP3 (5V DC)and ICP4 (24V DC) on the AC drive board (p/n A03U H520 01). Replace the drive board as necessary.
SPECIAL NOTE : Solution contribution by KMBT (Japan) and Freddie Burnham, Production Print/SSD

Konica Minolta... | Answered Yesterday


C0200 - Cyan PC Drum Charge Corona Malfunction. Did you mess with this imaging unit? You won't be able to reset if the malfunction is still present.
---------------------------------------------------------------
Konica Minolta Error Codes & Solutions - http://www.kmcodes.com
Drum, Transfer Belt and Fusing Unit Firmware Reset - http://www.bizhubreset.com
Drum and Toner Chip Reset - http://www.chipreset.eu
Transfer Belt and Fusing Unit Reset Kit - http://www.resetkit.eu

Konica Minolta... | Answered 3 days ago


Guess what! If you place a telephone call to a Konica Minolta service agent and mention 190f you may solve the mystery.

Konica Minolta... | Answered on Jul 29, 2019


How to replace fusing unit in c253
7_13_2019_4_48_00_am.jpg

Konica Minolta... | Answered on Jul 13, 2019


What do you want to reset???

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jul 08, 2019

Not finding what you are looking for?
Konica Minolta Bizhub C652 Color&b/w Copier/printer/scanner/fax Network,finisher Logo

14 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Konica Minolta Office Equipment & Supplies

  • Konica Minolta Office Equipment & Supplies

Most Popular Question

bizhub c652 service codes

  • Office Equipment & Supplies
Loading...