Summit SPWD1800 Laundry : Washer/Dryer Combos - Answered Questions & Fixed issues

Google "my dryer is flashing error code
13, not working".

Summit SPWD1800... | Answered on Jun 28, 2014 | 233 views

I could not find a manual for your SPW2201SS, but I did find a manual for a SPW2200SS. (Look for clogged hoses, in and out!) Sadly it only lists three 'error codes' on Page 27 and they include: E10 E21 E31 Summit SPWD2201SS Washer download instruction manual pdf

Summit Washing... | Answered on Oct 28, 2018 | 193 views

On the Whirlpool Duet washer, try pressing and holding the End of Cycle signal button (on the far right of the control panel) for 3+ seconds to toggle the Control Lock on/off. See the manual here: and here: . The small print about the Control Lock is almost readable (with good eyesight/correction) in the control panel closeup of the GHW9400PL here: .

I hope this helps.

Cindy Wells
(When you turn off the washer, it will remember the last setting for the Control Lock. This ensures that the washer can't be accidentally started by a child or while you clean the control panel.)

Washing Machines | Answered Yesterday | 22 views

cannot spin my washing it always go back to rinse

Washing Machines | Answered 2 days ago | 368 views

Possible bad pressure switch. Some units have this built into the board. Also known as the load selector switch.

Washing Machines | Answered 2 days ago | 17 views

The pump intake is clogged with blanket lint.

Washing Machines | Answered 2 days ago | 23 views

Why is my washing machine not washing properly?
A common reason why your washing machines is not cleaning clothes properly is because the line leading from the detergent tray to the drum has become clogged up with washing up powder. This means that just a small amount of detergent actually reaches the drum - the rest of it becomes stuck behind the blockage.

Washing Machines | Answered 2 days ago | 15 views

You must mean when the AGITATOR is moving back & forth! The drum spins only in one direction. So...
The agitator is driven off a gear train in the transmission. If the noise is occurring during the AGITATOR’s motion, you’d best have that transmission serviced, and soon; before it could lock up and cause more serious damage.
Call around for estimates in your area for prices to replace the transmission if that is necessary. Ask for a parts and labor breakdown and for terms of the service warranty, which usually covers parts for about one year but labor for much less time. And be sure you use a technician qualified to work on your machine. You could even ask for a reference or two.
Don’t be afraid to have this service done, even on an older machine. If done properly it will serve for at least another 10 years. But if the cabinet is rusted and/or you’ve seen frequent repairs with this machine, replacing the machine is a better decision.
By the way, when you make a service call and inquire in a manner that reflects that you know about these things (like “I’m pretty sure the transmission is the problem because the noise occurs only when the agitator is operating”) you will gain more respect from a serviceman with integrity. He will know you’re serious about having this fixed and he might even suspect it’s already been looked at, so he may be more likely to give you his best price.

Washing Machines | Answered 3 days ago | 20 views

Hi Lori, you shouldn't have to grease anything on that machine. What is the problem with the washer that you think you have to grease it? If it's squeaking while it's in the spin cycle,it has a leaking tub bearing and the bearings need to be replaced. You should call your local repair company to check it out and give you a price quote. Hope that helps.

Washing Machines | Answered on Aug 10, 2019 | 44 views

Alarm Mines are a great deterrent. Imagine sneaking around and then the mine goes off and you think someone has shot you. :>) A friend kept having is garage broken into, he installed 12 gauge blanks in an alarm mine and never got visited after it was tripped one night.

Washing Machines | Answered on Aug 09, 2019 | 29 views

Refer machine manual for red light flashing fault code if any . Brake solenoid could be faulty or the main electronic board . Contact local registered whiteware technician for proper diagnosys , cheers .

Washing Machines | Answered on Aug 08, 2019 | 47 views

i don't know. most washers have a lid safety switch that must be indicating the door or lid is properly closed. please check this switch is working properly. i just used a volt meter on a top loader. the lid switch was damaged.
if no water coming in, check hot and cold water are turned on. if no water, shutoff taps and disconnect both hoses at washer and the taps.[ most hoses have a wire screen in hose that may be plugged ]. if all seems clear, reconnect tap hose ends. hold hoses into sink or pail and check each is running free by just turning on taps a small amount. if hoses are OK, it may be the electrical connection to the water solenoids. inspect to see if connections are secure. if all seems OK, it may be a plugged or faulty switch/tube that is indicating the empty machine is full of water.

Washing Machines | Answered on Aug 07, 2019 | 36 views

recently repaired top loading machine by adjusting the lid safety switch. it needed adjusting so the pointer on the lid would make proper contact with switch, when closed. don't by pass this safety feature.

Washing Machines | Answered on Aug 07, 2019 | 40 views

taps are made to operate properly in any position of open or partly closed.

Washing Machines | Answered on Aug 07, 2019 | 45 views

Not finding what you are looking for?
Summit SPWD1800 Laundry : Washer/Dryer Combos Logo

Popular Tags

12 questions posted

Ask a Question

Usually answered in minutes!

Top Summit Washing Machines Experts

ray gallant
ray gallant

Level 3 Expert

63706 Answers

 Russ Hill
Russ Hill

Level 3 Expert

4048 Answers

Bill Boyd

Level 3 Expert

53745 Answers

Are you a Summit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides