20 Most Recent Konica Minolta bizhub C250 All-In-One Laser Printer Questions & Answers


machine trouble sevice call [c2558] wat a problam in konica minolta bizhub 164 printer

Konica Minolta... | Answered Yesterday


what lamp error

Konica Minolta... | Answered on Feb 18, 2019


Hi this kind of errors how came u should mention frst


may ne after you removed the board and then came ?

or while working suddnetly came ?


please specify

Konica Minolta... | Answered on Feb 07, 2019


Sometimes just open the doors and closing them a few times will work its sensing somethings open ,Make sure all is closed you may have too reinstall drivers. start over read all directions sometimes we get burnt out on trying to get something going give it a break for a bit then try again. could be a firewall or anti virus cause problems to.

Konica Minolta... | Answered on Feb 05, 2019


Are you using a 3rd party image unit???, if so get OEM there are chips on them that copier monitors. The image units are the units below the toner cart. which one is having the problem Y M C or Black, did you re chip them, bad idea. Replace them with OEM cartridge.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Feb 05, 2019


hi piz Error code P9 and P21 appears on screen and when printing or photocopying using color black, blank copies are outputed

Konica Minolta... | Answered on Oct 26, 2018


Most likely there is paper stuck in the very back behind one of the trays. Take both trays out and see if there is any paper jammed (could be a small piece). Put trays back in but leave them open, turn off the printer, unplug it, wait 5 minutes, plug it back in, turn it back on and push in the trays.

Konica Minolta... | Answered on Sep 24, 2018


It is a fuser error.

Try resetting. To reset a Rank A error follow these steps:

1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the Main Power Switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If the error recurrs then do the following:
1 Check the Fusing Unit for correct installation (whether it is secured in position).
2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary.
3 Change Fusing Unit
4 Change PWB-M
5 Change PU1

Konica Minolta... | Answered on Jun 26, 2018


tis error means abnormal tonder density in the balck image unit take the blacke image unit out and shake it while holding it level and put it back in the machine to reset the error code leave the machine on and open then close the front door

Konica Minolta... | Answered on Jun 22, 2018


Does this happen when copying? Can you print internal copier form meter count etc.?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 20, 2018


76e2129.jpg
Hope this helps. Make sure you remove the waste tank prior to taking out the transfer belt. Belt is removed by two screws inside right door and sliding the unit out.

Konica Minolta... | Answered on Jun 14, 2018


Turn OFF the Main Power Switch.

2. Turn Main Power Switch ON while pressing the Utility/Counter key. (Sub power must be "on" located on side of the control panel)

3. Touch [Trouble Reset].

4. Check to make sure that [OK] is displayed and the it has been reset.

5. After turning off the Main Power Switch, turn it on again more than 10 seconds after




Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 14, 2018


There is no procedure to restore the admin password. It is possible to reset and enter a new password, and for that you will need a technician to make the adjustments on SERVICE MODE (stop,0,C).

Konica Minolta... | Answered on May 18, 2018


no such code for a C250

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 25, 2018


1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Reset key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 25, 2018


Its looking for the fax board ??? Some one remove it????

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 25, 2018


NVRAM error when the main board was replaced was the NVRAM module replace was this a new board or one from a different machine if so you machine is junk. Have tech come out to re-flash firmware get a new board etc if he can

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 18, 2018


the control board can not talk to the hard drive was the hard drive replaced?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 18, 2018


see the previous post sir mam

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 18, 2018


You must have access to the a secure KonicaMinolta web site, need a tech to come out

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Mar 18, 2018

Not finding what you are looking for?
Konica Minolta bizhub C250 All-In-One Laser Printer Logo

1,250 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6825 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

bizhub Konica Minolta

  • bizhub Konica Minolta

Most Popular Question

clear error message c 2558 konica

  • Office Equipment & Supplies
Loading...