Kyocera FS-1135MFP w/ Document Feeder - Answered Questions & Fixed issues


The Error is described in the Service Manual as - "Zero cross signal error The zero cross signal does not reach the control PWB for specified time."

This can be a damaged wire harness between the High Voltage PCB and another board or a defective Power Source PCB. Bad power at the outlet can also cause this.

Move the machine to another location and make sure nothing else is plugged into the same line. If the problem goes away have an electrician check your wiring.

If the problem still occurs have a Service Technician check the machine and replace the bad part.

Kyocera... | Answered on Feb 27, 2015 | 239 views


SCAM - DANGER - DO NOT CALL THESE NUMBERS. These phony support numbers send you to criminal call centers where they will install malware, steal ID and/or extort money from you . Please only ever use the support contacts from the official company website

Kyocera Office... | Answered 15 hours ago | 11 views


....****WARNING THIS POST IS SPAM**** NEVER CALL ANY NUMBER POSTED ON FIXYA...NEVER. YOUR CREDIT INFORMATION AND COMPUTER ARE IN DANGER HERE......19

Kyocera Office... | Answered 2 days ago | 14 views


Log into the printers web page (ip address) select reset from the advanced page

Kyocera Office... | Answered on Oct 11, 2019 | 25 views


Check the battery on Main PWB.
Also maybe this occurs due to defective Main PWB.

Kyocera Office... | Answered on Oct 03, 2019 | 22 views


Replace the Process Kit.

Kyocera Office... | Answered on Oct 01, 2019 | 15 views


There is a jammed piece of paper some where in the feeder probably holding a switch actuator down

Kyocera Office... | Answered on Sep 28, 2019 | 20 views


Replace the FUSER

Kyocera Office... | Answered on Sep 28, 2019 | 17 views


Your message does not qualify as a question
DO NOT MAKE THIS SITE WITH YOUR GARBAGE
Take your GARBAGE to another Side
Your message qualifies as SPAM

Kyocera Office... | Answered on Sep 20, 2019 | 14 views


Check the document and then check the driver. Also check which control language the driver is set for. Also press the printer button on the op panel and then press "Go".

Kyocera Office... | Answered on Sep 19, 2019 | 1,409 views


Try to reflash/upgrade the firmware.

Kyocera Office... | Answered on Sep 18, 2019 | 15 views


Check the duplex actuator for remaining pieces of paper.

Kyocera Office... | Answered on Sep 18, 2019 | 18 views


Check the cassette's gears on the rear left and the motor inside the machine which drives the cassette's gears.

Kyocera Office... | Answered on Sep 18, 2019 | 27 views


Check the developer clutch. Maybe it is rusty.

Kyocera Office... | Answered on Sep 18, 2019 | 18 views


Enable Job Accounting. It is written in the Operation Guide.

Kyocera Office... | Answered on Sep 18, 2019 | 18 views


Your message does not qualify as a question
Your message qualifies as SPAM

Kyocera Office... | Answered on Sep 09, 2019 | 13 views


Call your local Kyocera servicer and report error code C6000.

Kyocera Office... | Answered on Aug 27, 2019 | 17 views


****WARNING**** THIS POST IS ALL SPAM..DO NOT EVER CALL ANY NUMBER POSTED ON FIXYA. YOU WILL BE SCAMMED AND LOSE CC INFORMATION...BEWARE...545

Kyocera Office... | Answered on Aug 26, 2019 | 15 views

Not finding what you are looking for?
Kyocera FS-1135MFP w/ Document Feeder Logo

16 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...