20 Most Recent Honeywell Programmable Thermostat Heater Questions & Answers


To turn the fan off, press the "fan key" until it says "auto". This will turn the fan off. When the programs scheduled, changes, the fan will go on again. You have to repeat the fan to "auto" each time the schedule changes.

Honeywell... | Answered on Sep 18, 2019


On the Pro4000 model you hold the 2 arrows until you go into setup mode. Then arrow up ONLY til you get to option 13. The display will read 13 and 1, press the DOWN arrow and it will read 13 and 0. This turns off Adaptive Intelligent recovery. Now hold the 2 arrows til you see the normal display screen. You are done.

I just did this with a Honeywell tech rep on the phone.

Honeywell... | Answered on Aug 16, 2019


Can be Low Battery Warning or Air Filter Reminder.


68307516_756645481420735_7688301075442434048_n-u3urdmfo3kv00dnpnoztjq21-2-2.jpg68289101_349062152645264_5909936129565523968_n-u3urdmfo3kv00dnpnoztjq21-2-0.jpg

Honeywell... | Answered on Aug 15, 2019


it gets its power from the unit via the data cable. go on the seely international website or the braemar website and they can put you in contact with another dealer in your area. get it fixed while still in warrenty.

Honeywell... | Answered on Jul 09, 2019


Thermostats can be found at amazon, take a look here: Defy Mother Nature with our Best Buy. I hope this was helpful. cheers

Honeywell... | Answered on Jul 03, 2019


Press Done on the thermostat if you aren't at the home screen. Then press Set Clock/Day Schedule at the bottom left of the touch screen. Then use the up/down arrows on the right to set the time. Press Set Day (second from the right on the bottom of the touch screen) then use the up/down arrows to set the Day of the week. Press Done to exit the set clock menu. (Alternatively, press Set Schedule to continue to set your thermostat to your daily schedule.)

Honeywell has the manual available on their site: http://yourhome.honeywell.com/home/ . Enter the model number in the search box to find the available manuals. See page E36 (28 of the PDF).

I hope this helps.

Cindy Wells

Honeywell... | Answered on Jun 22, 2019


Centigrade?

Honeywell... | Answered on Mar 02, 2019


you will have to reprogram it according to the operating manual.
The manual is available on www.manualnguide.com

Honeywell... | Answered on Jan 02, 2019


It sounds "locked". Refer to the installation/setup manual that came with the tstat for information on how to lock and unlock the thermostat.

Honeywell... | Answered on Dec 30, 2018


what's happened here is the cm61 ng and the reciver box have lost there connection you will have to "rebind" them then it will be fine -




THE BINDING OPERATION DESCRIBED BELOW IS REQUIRED IF:

· Any of the system components (room unit or relay box) are replaced

· HC60NG has incorrect or no binding data stored (e.g. when pre-bound system pack components have been mismatched)

· Interference with the RF signal has caused a communication failure

During the binding procedure keep approximately 1m distance between the room unit and the HC60NG

1 Turn off mains supply to HC60NG for 10 seconds. Re-connect supply.

2 Press and hold the HC60NG push button for 15 seconds to reset previously stored data. The red LED will start to flash at 0.1 s on/0.9 s off. Release the push button.

3 Press and hold the HC60NG push button for 5 seconds to enter the binding mode. Red LED flashing at 0.5 s on/0.5 off confirms the binding mode has been entered.

4 Move the CM67NG slider to the OFF position (CM61 push the OFF button) and press the TEMP , TEMP and PROG 1 buttons together. The CM61/67NG will display InSt.

5 Press the i button to send the binding signal. The red LED is switched off on the receiver box to confirm the successful binding operation. If the red light still flashes push the repeat steps 1-3 and press the the i button until binding is successful.


hope this is helpful

Honeywell... | Answered on Dec 05, 2018


Request the diagram directly from Honeywell.

Honeywell... | Answered on Dec 02, 2018


not finding a 153. open the cover, w2 or y2 means 2 stage, w or y is single stage

Honeywell... | Answered on Nov 12, 2018


It is to remind you once every 60 to 90 days depending on tstat n program to change filter reset filter reminder by pressing up arrow button next to wake button.

Honeywell... | Answered on Nov 01, 2018


Depends what kind of air handler or furnace you have. generally it will be a fan relay stuck.

Honeywell... | Answered on Oct 30, 2018


with the fan in the auto position, the fan only comes on during a demand for heat.  does it not come on during a demand for heat?

Honeywell... | Answered on Oct 30, 2018


no reset check batteries or consult you user manual for additional trouble shooting or can download manual from internet on honeywells site

Honeywell... | Answered on Aug 06, 2018


I have exactly the same problem, did you ever get an answer to this issue?

Honeywell... | Answered on Jul 07, 2018


Are you completely sure you have the Reversing Valve wire in the right place? Some reversing valves are powered for heat, some for cool. Make sure you know which yours is, or perhaps change that setting (see the manual) on the thermostat to try it.

ALSO, sounds like the FAN wire may not be in the right place either. Did you carefully note the wire colors on the old stat before you started, or perhaps take a photo?

Honeywell... | Answered on Feb 28, 2018

Not finding what you are looking for?
Heating & Cooling Logo

2,083 questions posted

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

606 Answers

Paul Carew

Level 3 Expert

3455 Answers

Cindy Wells

Level 3 Expert

6032 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Honeywell Heating & Cooling

  • Honeywell Heating & Cooling

Most Popular Question

white rodgers 153 7758 1 or 2 stage

  • Heating & Cooling
Loading...