Sharp AR-5316 Advanced Digital Imager Copier - Page 8 - Answered Questions & Fixed issues


all action bloked code: L6-10
please healp me

Sharp AR-5316... | Answered on Feb 19, 2013 | 947 views


driver to install to pc

Sharp AR-5316... | Answered on Feb 12, 2013 | 98 views


you may gey the driver software for AR=5316 printer install sotware inthese websites
http://nodevice.in/driver/AR-5316/get47086.html
http://ptf.com/sharp/sharp+ar+5316+printer+drivers+to+support+windos+7/

Sharp AR-5316... | Answered on Feb 12, 2013 | 652 views


F2 If sub code is 02 that s toner supply problem .if sub code is 04 that is identification problem model error or data abnormality.do not forget to rate the solution.by MIAN JEE

Sharp AR-5316... | Answered on Feb 10, 2013 | 1,848 views


E7-11 is a white level shading correction error. This code was intended to identify a dirty white level reference (located under the left edge of the copyboard glass).

This code has plagued certain individual Cougar machines. I have personally replaced CCD's, installed a foam damper to the top of the hard drive (to damp vibrations between the hard drive and the lens cover), and ICU boards, to no effect. Typically 3 to 7 times a day this code can pop up.

Sharp AR-5316... | Answered on Jan 30, 2013 | 506 views


Main Charge Corona shorting down, drum grounding issue, etc... Replace the process unit.

Sharp AR-5316... | Answered on Jan 30, 2013 | 23 views


Reset What Exactly?

Sharp AR-5316... | Answered on Jan 30, 2013 | 15 views


My sharp xerox AR 5516 is not working and it appears F and 2 signal

Sharp AR-5316... | Answered on Jan 22, 2013 | 30 views


Hi i think the problem code for f2 problem is to enter this code pressing * interrupt CA interrupt then the light will go of then you enter 80 then press copy and 1 copy.

Sharp AR-5316... | Answered on Jan 15, 2013 | 313 views


Have you tried to replace the toner???? Are you sure the light that is blinking for the toner?????

Sharp AR-5316... | Answered on Sep 28, 2016 | 672 views


You have used wrong toner cartridge....please use this model AR 202T

Sharp AR-5316... | Answered on Jan 11, 2013 | 114 views


press:
# --> interrupt --> clear --> interrupt
20 --> start --> 1 --> start

Sharp AR-5316... | Answered on Jan 01, 2013 | 24 views


if u take copy from adf scanner then clean the scanner glass. if the line is coming on print & copy both then check drum is there any line

Sharp AR-5316... | Answered on Dec 26, 2012 | 96 views


change the main charger because based on my experienced it has an arching problem

Sharp AR-5316... | Answered on Dec 08, 2012 | 1,216 views


An H2 is an indicator that the temperature sensing device is reading open, preventing the machine to warm up. There is only one way to correct this and that is to replace the thermistor, and that takes a technician. Not a hard job but a novice could get into trouble and make matters worse. Aloha, Bill Monroe

Sharp AR-5316... | Answered on Jun 02, 2013 | 1,647 views


i want a driver for charp ar-5316e

Sharp AR-5316... | Answered on Jun 07, 2013 | 578 views


I don't know

Sharp AR-5316... | Answered on Nov 21, 2012 | 575 views


Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.
  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.

Sharp AR-5316... | Answered on Nov 05, 2012 | 209 views


replace the CRUM chip
replace the develoing unit

Sharp AR-5316... | Answered on Oct 28, 2012 | 18 views

Not finding what you are looking for?
Sharp AR-5316 Advanced Digital Imager Copier Logo

1,371 questions posted

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

k24674

Level 3 Expert

8081 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...