20 Most Recent D-Link 802.11g Wireless Router WBR-1310 (WBR1310) - Page 5 Questions & Answers


I suggest you RESET the D-Link back to the default setting and configure the wireless settings again.
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

D-Link 802.11g... | Answered on Jun 18, 2011


do a search on the internet and find out how to reset the router, then you can enter a new password

D-Link 802.11g... | Answered on Jun 14, 2011


if this is on the computer enter it in the box that comes up when you turn on the wireless, if it is in the router config go to 192.168.0.1 in internet explorer, put in your user name and password (admin, admin) unless you changed it, and enter it under security settings. You should make sure that you have a password on your dlink so that no one gets free internet from you.

D-Link 802.11g... | Answered on Jun 14, 2011


Try doing a factory reset on the router.

Hold down the reset button for 20 seconds and let it go through its reset.

Please rate my solution to show your appreciation!

For more tips visit my blog at http://thegeektweet.wordpress.com

D-Link 802.11g... | Answered on Jun 04, 2011


You have to reset the router and login with default password.

D-Link 802.11g... | Answered on May 08, 2011


After you change the settings you must "apply" or click "Update" the settings on the router, when you finished, or else it will not be permanent.

D-Link 802.11g... | Answered on May 06, 2011


If you hold the reset button in for around 30sec this will erase all the settings everything will be there but it will be like it just came out of the box.

D-Link 802.11g... | Answered on May 05, 2011


Hi, There. You should try to reset the router. There's a small hole in the back that you must press with a needle or something similar for about 30 seconds. After all lights turn off and back on, your password should be the factory's original, usually Admin as username and no password.

Good Luck!

D-Link 802.11g... | Answered on Apr 30, 2011


To reset your router's password. The easiest way to do so is to check the back of the router you should see a reset button. Press and hold for 30 seconds.

D-Link 802.11g... | Answered on Apr 24, 2011


If you have a working Windows wireless machine, you can extract the key from the Windows machine and use it on your other devices.
Download this: http://download.cnet.com/WirelessKeyView/3000-2092_4-10614187.html
and then run it.

You can learn the WEP or WPA key in use which you can then use on other devices.
If there are no other working wireless devices, you will need to log on to your access point and reset the password there. The instructions for that depend on your access point.

D-Link 802.11g... | Answered on Apr 21, 2011


You do not need an installation CD to configure the D-Link wireless router

Connect a LAN cable from the D-Link to your laptop/computer's LAN port, open the browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)

You can now change the default password.
You can now configure the wireless settings.

You now configure the wireless card in your computer with the D-Link's wireless settings so the computer can connect to the D-Link via the wireless.


To secure your wireless network from unauthorized access, please click on this link and follow my instructions :-

http://www.fixya.com/support/r3559128-wireless_router_security

D-Link 802.11g... | Answered on Apr 16, 2011


You do not have to use the cd.
Shutdown your PC. Unplug the power from the router and the cable modem.
Wait 30 sec. then plug in the power to the cable modem, wait 30 sec. then plug the power to the router. Wait till you have "Internet" light then restart your PC. The PC should pick up an IP address and you should be able to get on-line. This is if you have a cable service provider. If you have DSL, the router needs to be configured with PPOe.


To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).

Enter the user name (admin) and your password. Leave

the password blank by default.


Find the manual on this link, slow link but you can read it online.:
http://www.scribd.com/doc/4040609/wbr1310-manual-110


Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe








I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

D-Link 802.11g... | Answered on Apr 12, 2011


you have to set the router according to your (Internet Service Provider) ISP's informations... What type of connection your ISP is??? PPPOE?? Automatic DHCP??? are you trying to set it up through wireless, you should NEVER setup a router through wireless (ALWAYS perform settings through wired connection)...

D-Link 802.11g... | Answered on Apr 10, 2011


The file bcmwltry.exe is the tray bar process for the Broadcom Corporation Wireless Network software.

You can try eliminating the program from start up.
Click on Start >>Run, type "msconfig" (without the quotes), then click on OK.

When the System Configuration Utility loads, click on the "Start Up" tab, then scroll down to the "bcmwlt.exe" entry and UNCHECK the box next to it.

Click on Apply, then OK, and the computer will need to be restarted. Do it. Upon restart, you'll see a System Configuration Utility warning. Simply choose the option to stop it from repeatedly opening.

This will be fixing your problem
Have a great day!
Pablo :-)

D-Link 802.11g... | Answered on Apr 05, 2011


Hi,

Welcome to Fixya. If you want to reset the router all you need to do is to press the reset button at the back of it for 5-10 seconds using a pen or paperclip. Make sure that the router is turn on and you will see the light will start flashing when you poke the button.

If you have questions please let me know. Thanks for using Fixya

D-Link 802.11g... | Answered on Apr 03, 2011


Hi,
Connect modem lan cable to Router Wan / Internet port. From Router Lan port you can either connect your system or switch . wireless : Scan for wireless network from your wireless system. If it shows, connect to your wifi network
Thanks

D-Link 802.11g... | Answered on Mar 25, 2011


At first you need to have the password in order to change it. If you don't have it, you can reset the router to its factory default configuration. To do that, look on the back of your router. There should be a small hole that only a sharpened pencil or pen tip will fit in. There is a button inside that hole. You want to make sure you press the reset button down for about 15 seconds and make sure the lights flash on it when you do that. Your router will reset to the factory defaults.

D-Link 802.11g... | Answered on Mar 20, 2011


The first thing you should try is the simplest: turn your router off, and let it rest for a moment. After turning it back on and allowing it to completely start back up, restart your computer, X-Box, and all other things that it might not be working on, to be sure that they are picking up it's new signal.
If nothing has changed, make sure that all of the proper wires are plugged in for your router.
If none of these basic steps are working - what error messages is it giving you? Is your X-Box360 simply not picking up the wireless signal? Does your computer's wireless connection still run smoothly?

D-Link 802.11g... | Answered on Mar 20, 2011


Hi,

SSID is the name of the network you can access the wireless settings page to check the network name and you canl personalize it aswell.

Thanks

D-Link 802.11g... | Answered on Mar 19, 2011


Please provide more information as to you issue such as :
a. model number
b. year manufactured/firmware updated
c.Are you using router wirelessly or hard connected.
d. You have checked the user manual 1st.
e. You have confirmed that you have connectivity with the ISP ( internet service provider)
f. uninstall/ reinstall the router software with the CD provided from the manufacturer.

D-Link 802.11g... | Answered on Mar 18, 2011

Not finding what you are looking for?
D-Link 802.11g Wireless Router WBR-1310 (WBR1310) Logo

780 questions posted

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

D-Link Computers & Internet

  • D-Link Computers & Internet

Most Popular Question

secure dlink wireless connection

  • Computers & Internet
Loading...