20 Most Recent D-Link 802.11g Wireless Router WBR-1310 (WBR1310) - Page 8 Questions & Answers


Press the reset hole on the back of the router in with a pen for at least 30 seconds. This will reset your router to factory settings

D-Link 802.11g... | Answered on Dec 30, 2010


Most routers don't require discs and the disc usually contains mere documentation for configuration and help. Routers are usually plug-and-play type devices but if you're definitely wanting some type of program or information. You can visit the below link for your router.

http://www.dlink.com/products/support.asp?pid=474&sec=0#applications

You'll need to specify by clicking the "Click Here" based on the revision of your router (A, B, or D). Once you've selected a revision, you'll be able to download the application and firmware updates for your router.

D-Link 802.11g... | Answered on Dec 30, 2010


check whether it wants security key.ask service provider for default key. or signal strenght might be low.

D-Link 802.11g... | Answered on Dec 30, 2010


A way to get around this issue is to do a static ip address for the other devices in your home. You'd have to connect to the router and set it up, i believe its by MAC address and you assign the IP.

-mk3ride

D-Link 802.11g... | Answered on Dec 30, 2010


Yoy may want to look into changing the channel that it is broad casting on. Most routers have 1-11 channels that you can select to avoid others that are broadcasting on the same channels. Also Wireless telephones, microwave ovens, etc. operate at near thye frequencies of some of the channels and may interfer, thus causing dropped signals. Go into your set up and select a channel other than the default 11, maybe? or another until you correct the problem.

D-Link 802.11g... | Answered on Dec 27, 2010


Your modem most likely needs to be powered-off for about 15 minutes in order for the NVRAM to clear the MAC address of the device that you previously had connected to it.
Unplug the power cord from the modem and wait about 15 minutes with the power off. After the 15 minutes, connect the router to the modem with the Ethernet cable and plug the power cord of the back in to the modem. One the modem has completed its startup, it should then work with your router.
If this does not work, then you may need to call your ISP to have them remotely clear the old MAC address from the modem so that it will work with your router.

D-Link 802.11g... | Answered on Dec 24, 2010


in back side of router you will find small hole for reset, please push that button for 15 second during power on then try to restart router.it will reset to default password.

D-Link 802.11g... | Answered on Dec 22, 2010


The WEP encryption key is in your router's wireless settings. Log into your router and got to the wireless settings, you will need to get the SSID and the WEP key. Then go to your computer/laptop's wireless card and configure it with the router's SSID and WEP key, so it will then connect to the wireless router and the Internet.

To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security
.

D-Link 802.11g... | Answered on Dec 20, 2010


To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).

Enter the user name (admin) and your password. Leave

the password blank by default.

If you get a Page Cannot be Displayed error, please

refer to the Troubleshooting section for assistance.


The manual:

http://www.scribd.com/doc/4040609/wbr1310-manual-110


Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

D-Link 802.11g... | Answered on Dec 19, 2010


Go to D-Link - TechSupport FAQ.



If you need more help come back.

Post / thumbs / testimonial are welcome!

D-Link 802.11g... | Answered on Dec 17, 2010


yes you can, you need to manually configure settings

D-Link 802.11g... | Answered on Dec 16, 2010


Go to Dlink website and download the latest drivers/ firmware for your router. That may fixs the problem

D-Link 802.11g... | Answered on Dec 14, 2010


give the this ip to your pc 192.168.0.100 when connect with dlink adaptor with lan cable and sub netmask 255.255.255. (manul ip for connecting)

D-Link 802.11g... | Answered on Dec 13, 2010


Just reset it! At the back of the router is a small hole.With a toothpick or some like press gently for 30 seconds and wait for the router to start up again.Log in to http://192.xxx.xxx and start a new configuration.


If you need more help come back.Post / thumbs / testimonial are welcome!

D-Link 802.11g... | Answered on Nov 28, 2010


Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Click on wireless then wireless security Enable WEP then enter new password save settings and restart router .Then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa

D-Link 802.11g... | Answered on Nov 27, 2010


1st you need to configure the the D-Links wireless settings eg, the SSID and encryption, and the configure the wireless card in the computer/laptop with the D-Link's wireless settings so it can connect to the D-Link.
To secure you wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security

D-Link 802.11g... | Answered on Nov 27, 2010


Hello;
First connect via Ethernet. Then
  • Click START'RUN and then type CMD
  • At the black window with the prompt(cursor) type ipconfig and search "default gateway"
  • Type the gateway address in the browser ej: 192.168.0.1
This is for enter the web administration of the router. I don't know your revision. But I will get you the Hardware Version: A1 Firmware Version: 1.04
  • Aim for Status as the picture above
On the WAN section is the actual Internet. WAN = Wide Area Network. Your computer is actually on the LAN = Local Area Network. The Computer looks the address on the router, then the router go to the WAN for the information. But this is transparent to the user. If the WAN is in cero on the addresses, you have to check the installation. when the installation are correct power cycle the modem and the router and try again. Always connected via Ethernet cable. Hope to help! coquibiz.jpg

D-Link 802.11g... | Answered on Nov 26, 2010


You don,t need to reset your router password only if you can,t log in the router configuration page.



If you need more help come back.Post / thumbs / testimonial are welcome!

D-Link 802.11g... | Answered on Nov 24, 2010


You can reset the router.Here is how!

Step 1: With the unit on, place a paper clip into the hole on the back of the unit labeled Reset.

01.jpg

Step 2: Hold paper clip down for 10 seconds and release.

Note: Do not repower unit during this procedure.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

Note: The factory defaults username is admin, and there is no password.


If you need more help come back.Post / thumbs / testimonial are welcome!

D-Link 802.11g... | Answered on Nov 22, 2010


ome wireless networks based on the 802.11b or 802.11g standards transmit their signal in a narrow radio frequency range of 2.4 GHz. Various other electronic devices in a home, such as cordless phones, garage door openers, baby monitors, and microwave ovens, may use this same frequency range. Any such device can interfere with a Wi-FI home network, slowing down its performance and potentially breaking network connections.
The 2.4 GHz Wi-Fi signal range is divided into a number of smaller bands or "channels," similar to television channels.Many wireless products ship with a default Wi-Fi channel of 6. If encountering interference from other devices within the home, consider changing the channel up or down to avoid it. Some Wi-Fi channel numbers overlap with each other. Channel 1 uses the lowest frequency band and each subsequent channel increases the frequency slightly. Therefore, the further apart two channel numbers are, the less the degree of overlap and likelihood of interference.
If this won't work, Then consider buying a new wireless router as your current is deemed broken.

D-Link 802.11g... | Answered on Nov 21, 2010

Not finding what you are looking for?
D-Link 802.11g Wireless Router WBR-1310 (WBR1310) Logo

780 questions posted

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

D-Link Computers & Internet

  • D-Link Computers & Internet

Most Popular Question

secure dlink wireless connection

  • Computers & Internet
Loading...