20 Most Recent Konica Minolta Magicolor 2530 DL Laser Printer Questions & Answers


check your media guides and check the user setting of the printer at the printer and compare at computer printer properties

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Dec 21, 2017


IF YOU LOOK AT THE PRINTER FROM THE TONER BOTTLE END THERE IS A SMALL CLUTCH IN THE TOP LEFTHAND REAR CORNER OF THE PRINTER.
YOU WILL NEED TO REMOVE THE TOP COVER TO ACCESS IT.
IT IS BEHIND A PLATE BUT FASTENED TO THE MAIN FRAME OF THE PRINTER.
YOU NEED TO SPRAY INTO IT WITH SOME LUBRICANT LIKE WD40 NOT OIL.
THIS CLUTCH GOES RUSTY AND DRIVES THE CAROUSELL SO GIVES 15H CAUROSELL ERROR

Konica Minolta... | Answered on Feb 05, 2017


check the media

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jul 09, 2016


replace the fuser unit. and replace the transfer roller and belt,

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on May 05, 2016


I literally just fixed the same problem in my 2530DL.

Look at section 6.3.23 in this service manual for a nearly identical model http://printer.konicaminolta.com/drivers/other/Manuals/24_25/fs_2400s.pdf and notice the "Precaution for Reinstallation"

This Registration Roller Solenoid is an electromagnet-activated lever which controls the timing of the page's movement through the printer.
The manual notes that the space between the "flapper" and gear is critical for proper timing. In my case, the tiny foam pad at the bottom end of the flapper had apparently become compressed over time, resulting in the spacing going out of tolerance.

I removed the foam pad and replaced it with layers of electrical tape, adding layers until I found the thickness needed to make the printer work correctly (6 to 8 layers). Then I removed the tape and glued in a piece of hard rubber of the same thickness. (Tape is only a temporary measure as it can compress or become sticky after a while.) Everything is back to normal now!

Good luck!

Konica Minolta... | Answered on Apr 13, 2016


replace with a new one.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jan 24, 2016


replace the fuser unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jan 24, 2016


what do you mean not straight?? the document come out skewed? if so check the rollers for that draw also might be something in the paper path the paper hits causing it to skew

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jan 18, 2016


the laser is being blocked for that color remove the image units and clean the slit glass that the laser goes though

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Dec 28, 2015


check and make sure correct media is selected in print properties and select at the machine

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 15, 2015


The transfer belt is what places the image on the paper, which the belt receive from the drums. Get a new one or re-install the belt properly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on May 19, 2015


On windows it is ok?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on May 19, 2015


Verify the printer paper size settings and on PC the paper layout settings.

Konica Minolta... | Answered on Jan 03, 2014


GO HERE FOR DRIVER
onyxweb.mykonicaminolta.com/OneStopProductSupport?appMode=Public
CANT PUT IN FULL LINK WONT POST

Konica Minolta... | Answered on Aug 30, 2013


Thank you for your kind reply.
I'm not going by the readout - but by the fact that bits of paper get stuck under one or two of the final feed rocker/rollers,,,, and are a bu@@er to get out.
Kinolta Customer Service - AND MANAGEMENT - are aware of just how badly designed this paper feed system is, but will do nothing about it.
I have had to virtually strip this piece of carp down, just to give me a little more access,,,, even then, its more than a struggle.
Thanks again.

Konica Minolta... | Answered on Aug 23, 2013

Not finding what you are looking for?
Konica Minolta Magicolor 2530 DL Laser Printer Logo

134 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Magicolor Konica Minolta

  • Magicolor Konica Minolta

Most Popular Question

konica minolta magicolor 2530dl streaks

  • Office Equipment & Supplies
Loading...