20 Most Recent Lexmark X342n All-In-One Laser Printer Questions & Answers


http://support.lexmark.com/index?page=content&locale=en&productCode=&segment=SUPPORT&clearQuestion=Y&userlocale=EN_US&id=SO1912

Quoting from support.lexmark.com above:

Problem

Error: "936 Main Drive Motor"; Error: "936 Transport Motor"; Error: "937 Main Drive Motor"; Error: "937 Transport Motor"

Environment

The 936 and 937 error codes indicate that the printer thinks there is a problem with the main drive motor.

Solution



  1. If your printer is posting one of these errors, turn it off and let it sit powered off for at least a minute.
  2. While the printer is off, open all of the doors and covers on the printer. Also remove the toner cartridge. Make sure there is no paper jammed in the printer. Pay close attention to the area where the toner cartridge sits. The main motor is located just to the left of the toner cartridge.
  3. If nothing appears to be wrong with the inside of the printer, reinstall the toner cartridge and close all the doors and covers. Now power the printer back on. If the error does not return, try printing again.
  4. If the error does not return when you print, continue using the printer. If the error does not return after a few days, this may have been an isolated incident and the printer should be fine.

Lexmark X342n... | Answered on Dec 13, 2018


If you have snapped the lid switch or male end to sensor, you may have to jump out the door switch.

If not, see the attached link for information

Lexmark X342n... | Answered on May 21, 2014


This means that the photoconductor has reached the end of life; on other printers, this is called the drum. It transfers the toner onto the page during printing so that it will fuse to the paper. The replacement is $70 from Lexmark: http://www.lexmark.com/US/en/view/Ink/Toner%20&%20Supplies/X340,-X342-Photoconductor-Kit/catId=cat170003-category&prodId=3599-product . The replacement should last about 30000 pages.

To replace the unit after you get a replacement, open the front cover and pull out the print cartridge assembly by the handle. Put the assembly on a flat surface. Remove the toner cartridge by pressing the button on the assembly and pulling on the handle. Open the new photoconductor kit and snap the toner cartridge into place on it. Then slide the new assembly into the printer. The steps are shown here: http://support.lexmark.com/index?page=answerlink&userlocale=en_US&segment=SUPPORT&locale=en&url=http%3A%2F%2Fsupport.lexmark.com%2Findex%3Fpage%3Dcontent%26id%3DSO4365%26actp%3Dsearch%26viewlocale%3Den_US&productCode=&answerid=16777217&searchid=1397780403561 .

After installing this, you need to reset the photoconductor counter.
With the printer on, open the front cover and press and hold Stop for 5+ seconds. When you see Resetting PC Counter release the Stop button. Close the front cover when prompted to do so.

If this doesn't clear the error, try powering off the printer for 10 seconds. Otherwise, try unplugging the printer for a minute to reset the internal memory. If the unit still doesn't reset the counter, it may need service. Contact Lexmark.

I hope this helps.

Cindy Wells

Lexmark X342n... | Answered on Apr 18, 2014


pls, clean all sensor of your printer

Lexmark X342n... | Answered on Jul 29, 2013


how to clear the fax memory on x342n

Lexmark X342n... | Answered on Apr 21, 2013

Not finding what you are looking for?
Lexmark X342n All-In-One Laser Printer Logo

165 questions posted

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

X Lexmark

  • X Lexmark

Most Popular Question

hola tengo una lexmark x340

  • Office Equipment & Supplies
Loading...