20 Most Recent Connex CX-4300HP CB Radio Questions & Answers


write out a list of all the faceplates for that radio,neatly . Now tear them in strips so you can attach them to the wall,
Now take a dart and toss it at those nameplates and whichever one it hits is the one you want.

Connex CX-4300HP... | Answered on Sep 03, 2016


If you need this you are telling me that you do not posses a ham license there fore you shouldn't be using this radio.

Connex CX-4300HP... | Answered on Sep 03, 2016


remove top and bottom covers and locate the resistors on the bottom of the main PCB. Unsolder them and remove them ,thats it.
check out cb tricks for a picture of what to do .

Connex CX-4300HP... | Answered on Sep 03, 2016


pin 1 gnd
pin 2 audio
pin 3 tx
pin 4 rx

Connex CX-4300HP... | Answered on Feb 02, 2016


Brand new. ? it is still on 10meter... there is a conversion to make them work on cb frequencies.

although they should have tuned up and converted when you purchased it.. at no cost...

Connex CX-4300HP... | Answered on Feb 02, 2016


Take it to a good cb shop radioactiveradios do really good work on connex radios

Connex CX-4300HP... | Answered on Jan 12, 2016


you would need to take to a cb shop. if you never done this before.
its simple process..
should cost less then $25 to have someone do this. correctly.
they should even setup and tune it for that price also.. so its ready to go. tune ups should be free at a good shop. and there shouldn't be any bench fees involved. just saying. or thats how the shops are here in TX. anyways.

Connex CX-4300HP... | Answered on Jan 26, 2015


check the power switch contacts {ie do you get 13.8v at power on or after its fized a bit??? or roger bleep
pa circuit can do this also

Connex CX-4300HP... | Answered on Nov 23, 2014


RF gain or volume turned up all the way?

Connex CX-4300HP... | Answered on May 18, 2014


it has a diode in back of radio near power wires. If it got hooked up backwards one time it will blow this diode and fuses from then on. Replace that Black striped diode near transformer inside radio. its in the far right. You have to take radio apart and solder in a new one or get a pro to do it.

Connex CX-4300HP... | Answered on Oct 03, 2013


IT could??? peak power, 14-15volts yeah.. the 4300 should put out 80w by itself.. as long as you have a low deadkey ie 1-5watts it should be fine. just don't put high wattage into an amp like that.. it will get hot QUICKLY.!!.. make sure your swr's are low low low.. 1.7:1 or lower... so your not getting reflected power... i would put a wattmeter with swrmeter like a mfj. or vectronic cross needle meter inline just to monitor it.... they go for $75 @ most places. Good investment... call email if need more help

Connex CX-4300HP... | Answered on May 10, 2013


You need to mention what kind of antenna...a car mount or home mount.
Here is the owners manual: http://www.cbtricks.com/radios/connex/cx4300hp/graphics/connex_4300hp_om.pdf

Connex CX-4300HP... | Answered on Sep 07, 2012


Oin 2 may be grounding, or the relay contact is not opening to break the circuit of the recieve section. Or your SWR is so bad that what you are hearing is from energy transfer alone and copper corrosion can act as the detector diode.

Connex CX-4300HP... | Answered on Feb 19, 2012


Pin2 of the mic may be shorting to ground.

Connex CX-4300HP... | Answered on Feb 19, 2012


http://www.cbtricks.com/radios/connex/cx4300hp/index.htm
Beware there have been a few design changes thru the years be this should not matter as far as the owners manual goes.

Connex CX-4300HP... | Answered on Jan 21, 2012


You will need an SWR meter to check your antenna. FIRST.
I would find help at a local cb shop.. They SHOULDN"T CHARGE to help you SET the swr. only if you need a part or something ..
I don't charge to SET SWR"s .. only if the cust needs a insulating washer or another antenna, or new coax, so-239 etc... I would be glad to help you.. let me know if we can CB Shop Temple, TX
Any shop shouldnt charge you just to see if it works!!

Connex CX-4300HP... | Answered on Nov 29, 2011


  • Sounds like you had a problem with the antenna set up or the corresponding connectors. If not done and checked right you will get an SWR through the roof. When the SWR is high the heat is returned back down the coax to the back of radio and right to the final transistor and smokes it.

  • Your radio being in a box for 3 years should not have really had any effect on its performance. There could have been some dust collect in there. You might have had the power turned up to high. Pop the covers off and see if anything is burnt. That's the first step.

  • Hope this helps.

Connex CX-4300HP... | Answered on Nov 14, 2011


A new unit goes for $280 range
then conversion to run cb freqency $30.
Tune-up $50 you should get 70 watts older units 90 watts newer units

As far as the knobs go
Band D with channel 19 selected this is 27.185 citizen band if you radio has had the channel expansion done other wise it is not accessible.
Select AM
10 khz switch should be off
mic gain know depends on the tuning of your radio and mic choice.
rf gain full clockwise best reception you will just have to play with this knob and the squelch to your liking
Make sure the thing is working properly before you buy capacitors dry out and the connex radios are know for problems with their pcboards. good luck

Connex CX-4300HP... | Answered on Oct 03, 2011

Not finding what you are looking for?
Connex CX-4300HP CB Radio Logo

42 questions posted

Ask a Question

Usually answered in minutes!

Top Connex Radio Communications Experts

Chris

Level 2 Expert

197 Answers

Damon Nesselrodt
Damon Nesselrodt

Level 2 Expert

197 Answers

Ray Murphy

Level 2 Expert

68 Answers

Are you a Connex Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Connex Radio Communications

  • Connex Radio Communications

Most Popular Question

brand new connex 4800 dxl straight out

  • Radio Communications
Loading...