20 Most Recent Icom Tait Tm-8200 Programming Aplication Software Cd Questions & Answers


Here is your solution: http://www.mediafire.com/?zt2q5emwifra47q

azlanjj@yahoo.com Borneo/East Malaysia

Icom Tait... | Answered on Feb 01, 2016


http://www.icom.co.jp/world/support/download/manual/

Icom Radio... | Answered on Oct 10, 2019


You need to be a very good technical person with electronics to work on these. The issue is most likely a PLL board issue. You need to be able to troubleshoot to the component level. The service manual appears to be https://www.manualslib.com/manual/738448/Icom-Ic-706mkiig.html

Icom Radio... | Answered on Oct 09, 2019


it is available on web sight..download it.

Icom Radio... | Answered on May 21, 2019


Contact Icom directly to inquire.

Icom Radio... | Answered on May 20, 2019


Contact iCOM directly to inquire.

Icom Radio... | Answered on May 17, 2019


Sure sounds like a "low volts" reboot due to high current draw.
Are you measuring voltage at the radio itself, after any connector, fuse or circuit breaker? The voltage (at the set) should be slightly different between low and medium power tx. Use a good meter to confirm this. Is the power supply able to supply the current required at high tx power? Is a current limiter operating? A lead-acid battery in parallel with the PSU might be needed at high power.
At high power setting the radio will probably reset faster than a low power input voltage can be measured with a normal meter, so an oscilloscope might be needed to see the power input voltage as it happens (might be very brief).
Could RF be getting back into the power supply? Does it happen on both bands? Is the SWR good? Is the earth good? How long and how thick are the power wires? Is there any filter on the power supply wires (close to the radio)? If it's new there will be a warranty if it's a fault in the unit. Good luck :)

Icom Radio... | Answered on Apr 28, 2019


Que es el error? Aye un numero? Diga mas acerca de este problema.

Icom Radio... | Answered on Apr 08, 2019


YOU CAN NOT THAT IS ONLY DONE BY SERVICE PROVIDERS

Icom Radio... | Answered on Mar 25, 2019


You've probably already found the answer to this question but doing a search for D104 wiring to ICOM will show you what you need. If the connector is the 8 pin circular one, then the PTT and MIC connections are the same for all ICOM radios.

mic wiring d104-fo0tt3cfp45qqpkmnfdugzjn-1-0.png

Icom Radio... | Answered on Jan 12, 2019


I would check the charger contacts and make sure that they are actually touching the battery contacts. Also, if the battery is shot, the charger may not recognize that there is a battery in it!

You might want to try cleaning all of the battery contacts and the contacts in the radio. These often get corroded and can cause problems.

Icom Radio... | Answered on Jan 12, 2019


If the dial actually shows the 40M frequency, then the likely hood of the PLL not functioning is slim. My guess is that the band pass filter for 40M has a bad relay or steering diode in it. This happens more often than not and is a rather inexpensive repair. I have the same problem in my IC-706, except 20M is affected.

Icom Radio... | Answered on Jan 12, 2019

Not finding what you are looking for?
Icom Tait Tm-8200 Programming Aplication Software Cd Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Icom Radio Communications Experts

Perry Mellott
Perry Mellott

Level 2 Expert

147 Answers

Robert McClure

Level 2 Expert

161 Answers

Vincent G
Vincent G

Level 3 Expert

2361 Answers

Are you an Icom Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Icom Radio Communications

  • Icom Radio Communications

Most Popular Question

need tm8200 tait radio programming

  • Radio Communications
Loading...