20 Most Recent NetGear WGR614 Router Questions & Answers


You need to reset the router if the lights are flashing. Press the reset button at the back of the router for about 20 seconds then release it. Now unplug the power for 20 mins as well and plug it back in. Make sure your connection is right. PC connected to port 1 and modem to WAN or Internet port.

NetGear WGR614... | Answered on Dec 29, 2018


Hello.

You need to make sure your gateway, DNS IP address in entered correctly and your RJ45 connection has the Orange and Green light blinking..

Thanks


NetGear WGR614... | Answered on Nov 14, 2018


Factory reset the modem and upgrade to the latest firmware.

Are you connected via ethernet or wireless?

NetGear WGR614... | Answered on Nov 14, 2018


The orange blinking light indicates that it cannot obtain the DNS server from your ISP (internet service provider). You must contact your ISP and check whether your service is active.

NetGear WGR614... | Answered on Nov 14, 2018


You need to consult a qualified Technician.

NetGear WGR614... | Answered on Apr 17, 2017


Call NETGEAR technical Support. If they cannot help try this http://technicalsupport.blog.friendster.com

NetGear WGR614... | Answered on Apr 03, 2017


Please check your version WGR614v1 Product Support NETGEAR

NetGear WGR614... | Answered on Mar 04, 2017


No, you have a bad internet connection.

Sort that out first, try not to use wireless connection until you have established a good fixed cable connection.

Then test out the wireless connection.

NetGear WGR614... | Answered on Mar 08, 2015


Netgear is not a browser. It is a Router. For the sake of this question I would assume you were talking about the Router, what do you mean by "Lock"? You can change the default password, and no one will be able to access it. If you only want specific devices to connect to the router, you can:
1) Enable MAC Filtering
2) Disable DHCP, and assign Static IP addresses to the devices
3) Hide SSID (Not Broadcast it)

NetGear WGR614... | Answered on Mar 04, 2015


Go to netgear.com ,click on support and download the latest version,also go to Windows update .

NetGear WGR614... | Answered on May 22, 2014


Username: admin
password: password

NetGear WGR614... | Answered on May 02, 2014


Go to windows logo
in search box type cmd
in black screen type ipconfig /release
when completed type ipconfig /renew
try again if still no go do the following

reset to factory default

press and hold reset button during the whole process and only release when completed.

1)press reset button 30 seconds
2)remove power cable 30 sec
3)plug in power cable 30 sec and then release.

You should no be set for 192.168.1.1
username admin
password is password

If all fails check to see if the box is checked for wireless

NetGear WGR614... | Answered on Apr 18, 2014


First off you need to have a wireless connection,that being said if you have one then you will need to go to your device and let it search for your wireless router.Once that is done and you enter any password you may have on your router it should connect.I seen had issues with this because the wireless signal can be weak if so to resolve this use a POE (Power Over Ethernet) or a direct wire from your router and select a wired connection.

NetGear WGR614... | Answered on Apr 18, 2014


yes

NetGear WGR614... | Answered on Nov 21, 2013


have you tried admin and password? The defaults if you haven't changed them.

Or if you did.

Reset for most routers with a reset button on the rear panel
Write down configuration information such as IP addresses, security keys, opened ports and services, etc., that you modified. (The default username is admin and the password is either password or 1234. Try these before resetting the router.)
  1. Press the reset button on the back until the test light blinks. This takes about 10 seconds. (To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)
  2. Release the button.
  3. Wait for the router to reboot.
  4. Log in with the default password. If the router was not cleared, try these additional steps AFTER the router has finished rebooting.
  5. Unplug the router's power.
  6. Press and hold the reset button. While the button is held down, reconnect router's power.
  7. Continue to hold the reset button for 20 seconds after reconnecting the power.
  8. Wait for the router to reboot.
  9. Log in with the default password.

NetGear WGR614... | Answered on Aug 08, 2013


Connect a LAN cable from the Netgear to the LAN port on your computer, open a browser and enter the Netgear configuration URL -
http://192.168.0.1
The default login = admin
The default PW = password You can now change the default admin password and configure the wireless settings.
Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access.
Now apply these settings to the wireless card in your laptop/computer.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

NetGear WGR614... | Answered on Mar 08, 2013

Not finding what you are looking for?
NetGear WGR614 Router Logo

322 questions posted

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

NetGear Computers & Internet

  • NetGear Computers & Internet

Most Popular Question

download smart wizard instalation

  • Computers & Internet
Loading...