20 Most Recent Krups Small Appliances Espresso Machine - Page 8 Questions & Answers


Chalk in the system, let it run a couple of times with plain vinegar. just fill the machine with about half a liter (one water container) vinegar and collect the vinegar in a cup so you can reuse it. run the full 0.5 liter, wait an hour and repeat. Than run 2 full watercontainers plain water. should work again. Cheaper than antichalk fluid and works the same

Krups Small... | Answered on Jun 23, 2010


mcdevito75 here You should be able to contact online, type in the appliance name in search and see about instructions on how to use or instruction guide replacement.

Krups Small... | Answered on Jun 20, 2010


If google and manufacturer website are of no help then ask a search agency like http://manualfox.com - They do a great job.
The service is not for free, but often worthy (you only pay if they find what you are asking for).

Krups Small... | Answered on Jun 18, 2010


Inside the water tank there is a magnetic float which is causing the problem. This float is moving always on the top of the water tank as you fill it with water and in reverse as the water level goes down then the float is moving down to bottom also. So as the magnetic float is moving up and down is giving the signal for the water level if it is full or empty.
So possibly now the float is stuck in the bottom and even if you have refill the tank this is still on the bottom of the tank. This can happen from many reasons. First could be that the plastic column that the float is moving is full of scale and it can not move up and down freely any more so you can clean it from scale by decaling it and even clean it with a wire brush.
A second possibility could be that float have a tiny hole and some water enter in the float and this make it to stay on the bottom of the tank. You can visually inspect it and if possible you can dry out the water and weld with a super glue the hole if possible, if it can not be fixed then you need a new float.
If you wand to fix it temporary until you find a new float you can a plastic clip or similar to secure it always on the top however you when the tank is empty it doesn't register so you would really have to keep an eye on the water level to avoid any other problems with the machine.
Good luck

Krups Small... | Answered on Jun 16, 2010


Hi,
As you have not mentioned what kind o specific iinformation you are seeking in regards to your product, I ma forwarding the link for the manual to start with which should cover things you should be looking for:
http://www.krupsonlinestore.com/manual/56222.pdf

Please let me know if you need further information.

Krups Small... | Answered on May 18, 2010


visit ApplianceInsider.com. They have a great database for manuals and if you can't find it there email them, they can probably get it for you.

Krups Small... | Answered on May 13, 2010


You can just removed the water tank filter (the cylinder inside the water tank) and washed it up. (Actually the filter should probably be replaced). Fix it back in the water tank and tide it safety upon the exit ring.

Don't forget to unplug the machine BEFORE doing this.
Next, restart the machine and let it perform the automatic self testing.

Krups Small... | Answered on May 10, 2010


Mine had the same problem ... all the lights are on, but no heating on the plate, and no dripping of water.

After a weekend on the workbench, I've mastered this machine. The KM7005 has 2 x MicroTemp G4 thermal cutoff (TCO) fuses which interrupt the Live line, for overheat protection. Mine didn't overheat per se, but the TCO blew anyway. Not reset-able ... need to be replaced with a soldering iron. I'll be happy to advise you to fix this, or fix it for you. Write me at KM7005@flightsystems.biz.

Krups Small... | Answered on Jan 31, 2010


Mine had the same problem ... all the lights are on, but no heating on the plate, and no dripping of water.

After a weekend on the workbench, I've mastered this machine. The KM7005 has 2 x MicroTemp G4 thermal cutoff (TCO) fuses which interrupt the Live line, for overheat protection. Mine didn't overheat per se, but the TCO blew anyway. Not reset-able ... need to be replaced with a soldering iron. I'll be happy to advise you to fix this, or fix it for you. Write me at KM7005@flightsystems.biz.

Krups Small... | Answered on Jan 31, 2010


First, press the PROG button. Now it's in PROGRAM mode. While the light is flashing, use the HOUR and MINUTES button to set the time you want the machine to fire up and start brewing. When you're done, just press no buttons for a few seconds till the light stops flashing. That ends program mode, and you're all set.

Write me at KM7005@flightsystems.biz if you need more help.

Krups Small... | Answered on Jan 31, 2010


The heating plate is actually your hot water heater for the unit and it has most likely failed. The water flows through the heating plate and heats the water for brewing. Krups replaced my whole coffee brewer.

Krups Small... | Answered on Jan 31, 2010


Mine had the same problem ... all the lights are on, grinding works fine, but no heat on the plate, and no dripping of water.

After a weekend on the workbench, I mastered this machine. The KM7005 has 2 x MicroTemp G4 thermal cutoff (TCO) fuses which interrupt the Live line, for overheat protection. Mine didn't overheat per se, but the TCO blew anyway. Not reset-able ... need to be replaced with a soldering iron. To date, I have helped 13 people on this site fix this exact problem.

I'll be happy to advise you to fix this, or fix it for you. Write me at KM7005@flightsystems.biz.

Krups Small... | Answered on Jan 31, 2010


Do you not take the glass body off, fill the top with coffee beans, put the top on and then just press down on the top of the glass top.

Krups Small... | Answered on Jan 17, 2010


water come from under the machine somewere

Krups Small... | Answered on Jan 06, 2010


If the pump is working, check the delivery pipe for blockage.

Krups Small... | Answered on Dec 27, 2009

Not finding what you are looking for?
Krups Small Appliances Espresso Machine Logo

298 questions posted

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Ray Murphy

Level 2 Expert

68 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Krups Coffee Makers & Espresso...

  • Krups Coffee Makers & Espresso...

Most Popular Question

manual krups il primo 972

  • Coffee Makers & Espresso Machines
Loading...