Krups Small Appliances Espresso Machine - Page 9 - Answered Questions & Fixed issues


you should call the experts to check it first if there are other things than usual

Krups Coffee... | Answered on Dec 04, 2018 | 44 views


If the thermoblock itself is the problem then I'd expect to read the element as open circuit because that's the only electrical part it has. The NTC that reads the temp is glued on with a special heat resistant glue, possibily it could be unstuck. The NTC's did suffer from solder failure where the wire terminal is. The NTC is only available as a new part complete with the thermoblock.

Krups Coffee... | Answered on Nov 23, 2018 | 98 views


Try this, remove the tank, the drip tray, the bin on the side and the sliding thing above the bin. Hold down the on and steam buttons while plugging the machine into a live socket, it's either that or the same again but holding down the on button and the program button while plugging it in. You will get a screen that says something like " Remis a something vende" which is French for put it into sale state, you choose "Oui" for yes. It's been a long time since I've done one but that's as best as I can recall. It will zero the coffee counters as well.

Krups Coffee... | Answered on Nov 23, 2018 | 510 views


Make your espresso as normal with the exception that you keep holding down the button until it has dispensed what you want to be the correct quantity. Next espresso you make will then be the correct quantity.

Krups Coffee... | Answered on Nov 21, 2018 | 473 views


have you cleaned the port holes that the coffee comes out of
there are tiny holes for the coffee to come through and they clog. use a fine wire to insert into the holes to unclog them.

Krups Coffee... | Answered on Nov 15, 2018 | 44 views


check for clog or test for failed element

Krups Coffee... | Answered on Nov 05, 2018 | 124 views


I'm not familiar with the model but I do know that you need to complete each and every step fully before the light goes out on the models I've worked on. Run through it again slowly before you worry yourself about a repair.

Krups Coffee... | Answered on Oct 24, 2018 | 122 views


????? ???? ese ??????????

Krups Coffee... | Answered on Oct 20, 2018 | 160 views


The heat sensor on the boiler is not detecting any temperature change. It could be a wire or terminal off. The sensor is right at the front of the boiler. If the sensor is faulty it means a new boiler because it's stuck on in the factory.

Krups Coffee... | Answered on Oct 02, 2018 | 208 views


Error 9 is only related to the NTC on the front of the thermobloc. That's the wires, terminals or the resistor on the NTC that changes value with heat.

Krups Coffee... | Answered on Sep 25, 2018 | 141 views


Contact Krups directly with your request.

Krups Coffee... | Answered on Sep 18, 2018 | 213 views


There are three things it could be, the motor that drives the brewing unit, the brewing unit itself or the pressure relief valve. You need to operate while looking inside with a torch to see what is happening. This is done with the back, the top and the beans side side cover removed for visibility.

Krups Coffee... | Answered on Sep 08, 2018 | 316 views


Fixya does not source parts

Krups Coffee... | Answered on Sep 03, 2018 | 85 views


Google (krups)(xp1020)(manual) without parens.

Krups Coffee... | Answered on Aug 23, 2018 | 104 views


Krups Optisteam Food Steamer with manual was for sale on ebay with a manual, but is no longer available.

https://www.ebay.com.sg/itm/Krups-Food-Steamer-Optisteam-649-With-Manuals/123088622624

Krups Coffee... | Answered on Aug 11, 2018 | 85 views


Error code 01 accompanied by that noise points at the distributor being faulty. The distributor is the electronic tap that directs water to the ram to compress the grounds in the boiler and then redirects it to the brewing chamber to make the coffee, then to steam, then to rinse. It's the sort of item you just replace because it's quite a large job to change it anyway, not the sort of repair you want to be doing over and over trying not to spend money on the part.

Krups Coffee... | Answered on Aug 02, 2018 | 536 views


You need to contact the service agent.

Krups Coffee... | Answered on Aug 01, 2018 | 277 views

Not finding what you are looking for?
Krups Small Appliances Espresso Machine Logo

298 questions posted

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Ray Murphy

Level 2 Expert

68 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...