Lexmark X4550 InkJet Printer - Answered Questions & Fixed issues


What is the error message you receive when you try to connect it to Wifi ?

Lexmark X4550... | Answered on Nov 13, 2015 | 76 views


Google the Internet for a power adapter for your model Lexmark printer. You will get various suppliers and prices.

Lexmark X4550... | Answered on Jan 31, 2013 | 59 views


The printhead on the cartridge could already be damaged thus the need to replace the cartridge.

Lexmark X4550... | Answered on Nov 04, 2012 | 45 views


There could be a problem with your printer software. Please insert your printer software installation CD into your computer hard drive. Execute the application to repair any possible corrupted printer software files.

Lexmark X4550... | Answered on Mar 13, 2012 | 112 views


The problem could be due to a communication failure between one of the printheads (cartridges) and the All-In One (AIO) or by a short in one if the printheads. Please follow the steps below to identify and fix cartridge issues:

  1. Make sure the printer is on.
  2. Open the printer cover. The print cartridge carrier moves and stops at the loading position, unless the All-In-One is busy. Note: If the carrier does not automatically move to the center, turn off the printer or unplug the printer from the power source and then carefully slide the carrier to the center.
  3. Remove both cartridges from the carrier.
  4. Close the printer cover.
  5. Re-brick your printer by pulling out the power supply - black box behind the printer where the power cord is plugged in to, and re-plug after 30 seconds.
  6. When the printer turns on, reinsert one cartridge first. Close the printer cover and check for any errors.
  7. If no error appears, reinsert the other cartridge. Close the printer cover.
  8. Replace whichever cartridge is causing the error to appear with a new genuine Lexmark cartridge. Try to print a document again to verify that the problem is fixed.

Lexmark X4550... | Answered on Mar 13, 2012 | 251 views


Try to reset the printer's wireless network settings. On the printer operator panel, press Setup button > Network Setup > Wireless Setup > Reset Network Adapter > press check to confirm.
Re-launch the Lexmark Wireless Setup Utility to connect the printer to your network. If you have a firewall enabled, make sure to allow full access to all Lexmark software and printer communication processes in the program rules/permissions for your firewall. Also, place your printer where it receives excellent wireless signal quality and away from other electronic devices which can cause wireless interferences (e.g. cordless phones, microwave ovens, baby monitors, garage door openers, and other wireless electronics).

Lexmark X4550... | Answered on Jun 30, 2011 | 180 views


Welcome to Fixya

Looks like the firmware of the printer hang up on you. Try to reset the printer back to factory default settings. Please see procedure below:

To reset to Factory Default settings, turn off the printer by pressing and holding down power button. Then release the button. Press and hold down Color Start and Cancel buttons while pressing and releasing the power button. Continue holding down the Cancel and Start buttons for at least 20 seconds then release it. You will then be prompted to go through the setup again. To reset the printer's wireless network adapter, press Settings on the operator panel > Network Setup > Wireless Setup > Reset Network Adapter > hit check to confirm.

Thank you for using Fixya!


If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Lexmark X4550... | Answered on May 23, 2011 | 115 views


There could be something that's blocking a printer communication process - firewall maybe? Make sure to allow full access to all Lexmark software and processes, especially lx??wbgw.exe (where ?? stands for any letters), in the program rules/permissions for the firewall. Also, on your computer, go to Start menu > in Run/Search bar, type services.msc and hit Enter > scroll down the items and look for lx??CATSCustConnectService > right-click on the service and select Stop. Try to print again.

Lexmark X4550... | Answered on May 12, 2011 | 336 views


If you're having trouble getting the paper jam from the feeder, you can open the cartridge area. You should be able to get a better hold of jammed paper out from there.

Lexmark X4550... | Answered on May 03, 2011 | 151 views


lexmark.com can provide that just paste the porduct model

Lexmark X4550... | Answered on Mar 27, 2011 | 18 views


you can buy them in pc world

Lexmark X4550... | Answered on Mar 02, 2011 | 20 views


I have tried to set up this wireless printer on my laptop (windows vista basic). I run through installation and get message - installation complete and the green indicator light is fully on. When I try and print I get message Printer cannot communicate with computer - please turn on 'Enable Biodirectional Communication' in printer properties. I go to control panel/printer/propertie/ports/ and I see Enable Biodirectional communication - the box is grayed out and I cannot enable it. Any suggestions?

Lexmark X4550... | Answered on Feb 26, 2011 | 1,363 views


hello bdas.... often the problem is the paper itself. Get a few sheets of paper from another source and try that. Joe

Lexmark X4550... | Answered on Feb 18, 2011 | 76 views


try to reinstall the driver of your printer then try again



akuma_Ryu21


dont forget to rate!!

Lexmark X4550... | Answered on Jan 24, 2011 | 65 views


Press SETTINGS on the control panel.
Press ARROW key left or right to DEVICE SETUP.
Press CHECK
Press ARROW key left or right to LANGUAGE
Press CHECK.
Press ARROW key left or right to language you want on display.
Press Check to accept.

Lexmark X4550... | Answered on Jan 24, 2011 | 72 views


Yes, the printer can scan documents for emailing. You can use the Lexmark Imaging Studio to scan to email. Go to Start menu -> Programs -> Lexmark 3500-4500 Series -> Lexmark Imaging Studio -> E-mail. Select the Photo, Several Photos, or Document option. Click Start. Click Create E-mail to have your images attached to an e-mail message.
For more information, you can refer to the Lexmark X4550 user's guide. For Windows, you can access the user's guide by going to the Start menu -> Programs -> Lexmark 3500-4500 Series -> User's Guide.
You can also download your printer's user's guide for free from the Lexmark website. Click on this link Lexmark 3500-4500 User's Guide.
I hope this information has been helpful. Thanks.

Lexmark X4550... | Answered on Jan 13, 2011 | 432 views


    Connecting to a Router
  1. 1 Check if your printer is network ready. Many newer models are designed to work on networks. Examine the documentation to see if your printer supports Wi-Fi (802.11x) or Bluetooth.
  2. 2 Add network support to your printer. If your printer is not already wireless you can connect it to a wireless router using the RJ-45 Jack (it resembles a large telephone jack). You can also buy an expansion card that will add a jack or buy an external print server that will connect to the USB or parallel port.
  3. 3 Connect your printer to the network. If your printer is not wired, you'll have to connect it directly to your wireless router. Connect a networking cable from the RJ-45 Jack on the printer (or adapter) to the router. Plug it into any jack except the UPLINK. The printer should automatically connect to the network when turned on.
  4. 4 Install printer drivers on all computers. Using the disc that came with the printer or drivers downloaded from the manufacturer, install the printer's drivers onto each computer on the network.
  5. 5 Print. You should be able to access the printer just like any other wireless device. Select the printer from the Print menu when you print.

Lexmark X4550... | Answered on Jan 07, 2011 | 62 views


Hi,

You can download the installation software from manufacturer's support website by clicking this link

On the page which opens, select the operating system of your computer (Windows Xp/ Vista..) from the drop-down menu. Then download the required software. (See attached image)

hmerchant110_33.png

The list of available software will load only after selecting the operating system of the computer.

Hope this solves your problem. Thanks for using FixYa

Lexmark X4550... | Answered on Dec 27, 2010 | 73 views

Not finding what you are looking for?
Lexmark X4550 InkJet Printer Logo

150 questions posted

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...