20 Most Recent Andis AGC2 Hair Trimmer Questions & Answers


If the latch has been pushed down without a blade on it you will need to get a flat head screw driver. Push up the blade lock and put the screwdriver behind the the tongue on the hinge. While pushing up on the latch push the tongue out with the screw driver. If you need any add'l assistance please call the Andis customer service dept at 1-800-558-9441.

Andis AGC2 Hair... | Answered on Aug 18, 2014


put a flat bladed screwdriver under the part of the hinge with two ridges on and pull it up.

Andis AGC2 Hair... | Answered on Aug 14, 2014


On the back of the clipper it should say something like AG, AGR, or AGC does it look like any of these dog clippers Dog Clippers .
Has it got a power cable or is it a Rechargeable? Also age is a good clue?

Andis AGC2 Hair... | Answered on Jun 24, 2014


Sounds as though the switch is faulty on the circuit board you can purchase new Andis parts here Dog Clippers

Andis AGC2 Hair... | Answered on Jun 24, 2014


If you look at the base of the blade at the bottom edge the is a black metal bar, push this in towards the blade and pull the nose of the blade away from the clipper.

Andis AGC2 Hair... | Answered on Jun 05, 2014


try replacing the blade drive assembly they wear in width.

Andis AGC2 Hair... | Answered on May 08, 2014


This round cylinder is a permenant magnet and doesn't actually connect to anything, the only contact which matter are the copper wires connecting the circuit board to the Carbon brushes.
This may be as simple as a faulty cable check for power to the circuit board.

Andis AGC2 Hair... | Answered on Feb 11, 2014


Sound as though the blade drive needs replacing, commonly you will notice tram lines in the cut on your longer blades or the shorter blades struggling to cut

Andis AGC2 Hair... | Answered on Feb 11, 2014


no diagrams but give us a call and we can talk you through it
http://www.angliaclipperservices.com/index.php?route=information/contact

Andis AGC2 Hair... | Answered on Feb 11, 2014


Drive bearings can only be replaced (safely) by removing the motor and then the armature.

Andis AGC2 Hair... | Answered on Feb 11, 2014


Instructions come in with a new drive assembly, basicly put the black end through under the metal frame first then push it down into place.

Andis AGC2 Hair... | Answered on Feb 11, 2014


You can find instructions on the following link
Fitting Cable

Andis AGC2 Hair... | Answered on Feb 11, 2014


Yep as simple as that just make sure they are a well recignised sharpener otherwise you will waste your money. You can rule out a clipper problem if other blades cut ok. Clipper Blade Sharpening

Andis AGC2 Hair... | Answered on Feb 11, 2014


Hi I know its a late reply but this sounds just like a power cord problem you can buy a new mains lead for the clipper from UK based company Anglia Clipper Services

Andis AGC2 Hair... | Answered on Feb 11, 2014


Ok if you take them appart don't touch the screws you will find it hard to re-align, if your blades haven't been sharpened for 5 years the i think its a very good place to start

Andis AGC2 Hair... | Answered on Sep 21, 2011


Neither the circuit board need jacking up with a washer either side or worst case a new Circuitboard.

Andis AGC2 Hair... | Answered on Sep 21, 2011

Not finding what you are looking for?
Andis AGC2 Hair Trimmer Logo

33 questions posted

Ask a Question

Usually answered in minutes!

Top Andis Health & Beauty Experts

Bruce Showalter

Level 2 Expert

133 Answers

shaveroutlet.com
shaveroutlet.com

Level 3 Expert

1639 Answers

Anthony Ward
Anthony Ward

Level 2 Expert

396 Answers

Are you an Andis Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Andis Health & Beauty

  • Andis Health & Beauty

Most Popular Question

used clippers

  • Health & Beauty
Loading...