General Electric Adora GHDA670N Built-in Dishwasher - Answered Questions & Fixed issues


Make sure you are installing that silverware holder properly. The little tabs of the silverware holder are supposd to go over and around the mating bars of the upper rack. Barring that, your upper rack may be pulled (bent) out, and you may have to push it (hard) to get it back in shape.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

General Electric... | Answered on Mar 03, 2015 | 93 views


Some dishwashers like your model number are under recall for a potential fire hazard due to water leaking through the heating element posts onto the wiring.
Your serial number must begin with the 2 letters listed . Below is the list of recall serial numbers: FL, GL, HL, LL, ML, VL, ZL, AM, DM, FM, GM, HM, LM, MM, RM, SM, TM, VM, ZM, AR, DR, FR, GR
Call the phone # below or check out GE recall website. What GE does is replace the element and gaskets, unless there is burnt or arcing visible on the wires, they may replace the dishwasher.

www.geappliances.com/products/recall
GE has determined that an electrical failure in the dishwasher's heating element can pose a fire hazard. GE will provide a free repair to all consumers with units affected by the recall. We ask that you not use your dishwasher until it is repaired and to disconnect the electric supply by shutting off the fuse or circuit breaker controlling it and inform all users of the dishwasher about the risk of fire.
Consumers who instead wish to replace their dishwasher with a new model can receive a rebate towards the purchase of certain new GE and Profile brand dishwashers. Consumers can use a rebate of $75 for the purchase of certain GE front-control plastic tub dishwashers, or a GE rebate of $100 for the purchase of certain GE front-control stainless tub dishwashers or GE Profile top control dishwashers. See the rebate form for eligible models.
GE is aware of 15 reports of dishwasher heating element failures, seven of which resulted in fire and smoke damage beyond the unit. No injuries have been reported.
The model and serial numbers are important, as not all dishwashers are included in the recall. Look at the inside on the front left side of the dishwasher tub to find the model and serial number.
This recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission, which will also monitor the effectiveness of the recall program.
Recall Hotline
866-918-8760
Monday through Friday, 8 a.m. - 5 p.m. ET.
Before calling, have the model and serial numbers on hand.

Customer Care

General Electric... | Answered on Apr 25, 2014 | 280 views


According to the GE repairman who visited, the solution is to close the machine (with the lights flashing). The machine starts and goes through the cycles, which it does rapidly and then all the lights turn off and the machine becomes silent after 1-1/2 to 2 minutes. Then the machine has been reset to normal. During this reseting period nothing happens inside the machine, although you may hear a running sound.

Thus, the solution is to run the machine in this flashing light state for the 1-2 minutes it takes to go raipdly through each cycle and then reset.

I hope this helps.

General Electric... | Answered on Jun 05, 2016 | 37,674 views


Perhaps the solution to your problem can be found in the User Guide- 

Your model number appears with two suffixes; WW and BB thatmay only be color codes but user guides (which appear to be identical) areavailable for download from GE’s site:
 
http://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-55031.PDF
 
 

General Electric... | Answered on Dec 31, 2011 | 1,927 views



Hi,

Here is a tip that I wrote that will help you with your dishwasher not draining problem...

Dishwasher Problems - Water will not drain out

heatman101

General Electric... | Answered on Apr 20, 2011 | 224 views


If you just want to shut it off, press the cancel button twice--If you press it once it will drain before shutting off

General Electric... | Answered on Sep 17, 2010 | 1,408 views


I have the same problem. If I turn the circuit breaker off (for 30 seconds) then turn it back on, the lights will light up, but the controls don't work. After several minutes, the lights go out again.

General Electric... | Answered on Jul 19, 2010 | 1,294 views


Hi,
Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...

Dishwasher2_bing.gif Trouble No Water entering Dishwasher2_bing.gif
http://www.fixya.com/support/r4021363-dishwasher_trouble_no_water_entering

heatman101

General Electric... | Answered on May 31, 2010 | 137 views


May I get the model # to help you more.

General Electric... | Answered on May 08, 2010 | 540 views


It sounds like you don't have enough water. Your water inlet valve may be not letting in enough water or the plastic pump inlet screen located on the bottom of your dishwasher had something blocking it.
  1. Check to see if there is something blocking the plastic screen on the bottom of your dishwasher.
  2. When your dishwasher is in the final cycle add a pot of hot water to the dishwasher and see if your dishes come out cleaner.
If the dishes come out cleaner you may need a new water inlet valve.

General Electric... | Answered on Dec 29, 2009 | 310 views


check to see if the arms are spinning properly

General Electric... | Answered on Dec 26, 2009 | 390 views


Very likely a bad timer switch.

Fortunatly, they are fairly easy to replace.

Just make certain you plug in all of the connectors that came off the old one into the same places that they cam off the old one.

General Electric... | Answered on Oct 27, 2009 | 279 views


To re- set can take up to 90 second's depending on the cycle, the door has to remain locked or it will not re-set. Our's had not been installed correctly, it had to be closed very hard to get it to lock, it was doing the same thing as your's. Hope this help's. That beeping is annpying.

General Electric... | Answered on Sep 21, 2009 | 1,017 views


Ours did the same thing. It had not been installed corectly. Try pushing in on the door then push the re-set button, it can take up to 90 second's to re-set, if the door isn;t fully shut it will continue to beep. If this doesn't work, unplug the unit for a few minutes to see if it will re-set. Good luck. We were up most of the night trying to find the owner's manual. Finally found 1 on GE's web-site.

General Electric... | Answered on Sep 21, 2009 | 342 views


If the door isn't fully closed it won't automatically lock. Our's was improperly installed so it really had to be closed hard to get it to lock. To re-set it can take up to 90 second's,the door has to remain locked during this time.Unplugging the unit may re-set it. the door Hopefully this will help out.

General Electric... | Answered on Sep 21, 2009 | 169 views


After downloading owner's manual off of GE web site we found out that our's had been improperly installed. If the door doesn't lock it won't cycle. To re-set it can take up to 90 second's depending on the cycle. If you stop it before the cycle is done it will continue to beep 'till you close the dorr , touch the re-set button & wait 'till it re-set's.

General Electric... | Answered on Sep 21, 2009 | 122 views


Down loaded owner's manual off GE site.
The door has to be closed enough to lock, if improperly installed it will not lock. It can take up to 90 second's to re-set.

General Electric... | Answered on Sep 21, 2009 | 242 views


HI. check the following areas for faults.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer or Control Board
Replace if defective (note: uncommon problem).

General Electric... | Answered on Aug 05, 2009 | 1,278 views


Is water filling into the machine at all? If not it is the fill valve. try www.repairclinic.com

General Electric... | Answered on Apr 20, 2011 | 335 views


HI. check the following areas for fualts.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer
Replace if defective (note: uncommon problem).

General Electric... | Answered on Jul 15, 2009 | 1,596 views

Not finding what you are looking for?
General Electric Adora GHDA670N Built-in Dishwasher Logo

71 questions posted

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4359 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...