20 Most Recent Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum Questions & Answers


Follow the link below to download a copy of the User's Guide.
http://www.bissell.com/searchresults.aspx?searchtext=25A3&searchType=search&mode=userguides
The wood floor cleaner will work on your tile.

Bissell ProHeat... | Answered on Aug 24, 2019


Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101
,

Bissell ProHeat... | Answered on Jul 24, 2019


If unit is not picking up solution it is most likely the small red plastic filter that is just above the small float door in the top piece just left of the tool switch.. pop it out clean muck out of it and it will work like new again.. have fun!!

Bissell ProHeat... | Answered on Aug 05, 2018


If I may! In most cases the heater is clogged. It might be clogged with soap that has harden over time. You need to take the handle apart. You will see a metal box(thats the heater) besides the wires there are two tubes connected to the heater. remove the tubes but label or watch which tube goes where. now turn the heater upside down. there are 6 screws on the side and 1 in the middle. remove them carefully. the 6 on the side have a small gaskets under them..you don't want to lose them. the 1 in the middle has no gasket, now the bottom plate of the heater can be taken off (there is a gasket with that plate ...be careful . you will now see the long channels inside the heater and need to clean it. the holes where the tubes where connected have to be clean also but carefully. the metal is soft.so it bends. now put it all back. hope this helps. if you want to keep this from happening.the best way is to run clear water after you are done.this will remove any soap in the machine which will harden after the machine drys out. hope I helped .

and to mr. reddevil6 I am learning lots from you. Thanks

Bissell ProHeat... | Answered on Jun 03, 2018


Not to be negative but I fixed one Bissell, and it worked for a while then it broke again. My Daughter bought one and it broke on her after using it only 3 times.

buy the rug Doctor or some other brand . That is my advise. Otherwise you will have to keep fixing that one.

Bissell ProHeat... | Answered on Oct 22, 2017


Check YouTube for something similar.

Bissell ProHeat... | Answered on Oct 08, 2017


Hello, this is Ava with Think Crucial.

Check to ensure there is a full tank of Bissell Hard Floor Solutions and water. - Make sure the clean water tank is inserted properly by removing the tank and re-inserting it. Ensure the gasket is attached to the water tank and did not fall into the machine. Reattach this gasket if necessary. - Check the valve on the bottom of the clean water tank. The water should come out of the X-valve when pressed. If the valve is blocked, soak the cap and insert in hot tap water until the blockage clears. Check the handle to ensure it is installed properly. Remove the handle and re-attach, making sure the handle is pushed down all the way. If you need to re-install the handle, remove the solution tank and lift the tab as you lift the handle. Check to ensure the solution tube is inserted properly into the floor nozzle. Clean the spray tips by bending a paper clip and inserting this into the spray tips to clean. If you continue to experience no spray, you may need to call Bissel at 1-800-237-7691 for further assistance.

You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

https://www.thinkcrucial.com/search?type=product&q=bissell

I hope this was helpful.

Ava B.
Think Crucial Customer Care
http://www.thinkcrucial.com/

Bissell ProHeat... | Answered on Nov 02, 2016


Hello, this is Ava with Think Crucial.

There are a number of reasons why your unit doesn't spray water. It could be that the !) water tank is empty which you can fill heavy duty bladder with hot tap water. 2) If Formula tank is empty, you can fill it with Bissell 2x formula for cleaning. 3) If tank may not be seated properly, turn the power off, remove and reseat the tank. 4) If pump may have lost prime, try to turn off and then turn on the unit, wait for one minute and depress trigger. If still nothing happens, I suggest you contact Bissell 1-800-237-7691 for further assistance.

I would like to let you know that you can order replacement parts for your vacuum needs. Please visit our website

http://www.thinkcrucial.com/search?type=product&q=bissell

As a special offer here is an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

Ava B.
Think Crucial Customer Care
http://www.thinkcrucial.com/

Bissell ProHeat... | Answered on Nov 02, 2016


There is a clear cover over the suction head that is held on with 2 screws. Remove the screws with a philips screw driver and the cover will remove providing access for cleaning. Refer to your owners manual which provides this info with a photo I think. Reinstall in the reverse manner. Be careful not to over tighten the screws as you could strip the threads. So to reassemble do not use an electric screw driver or drill type screw drive.

Bissell ProHeat... | Answered on Jul 30, 2016


Check dispenser seating, turn off unit, unplug unit. Reseat dispenser, plug in unit, turn unit on, wait one minute, press sprayer to test. While your at it clean the two filters. The filters need to be cleaned after each use. One is located under the Water Tank Cap and the other is under the Flow Indicator. Bissell Consumer Care 1-800-237-7691

Bissell ProHeat... | Answered on Jan 30, 2016


Check Consumer Care at 1-800-237-7691

Bissell ProHeat... | Answered on Jan 30, 2016


Most likely Water Tank Filter clog. The filter is located in the cap of the water tank (looks like a screen) remove it and clean and replace it. You may want to check the User's Guide for anyother filters that should be cleaned after each use.

Bissell ProHeat... | Answered on Jan 29, 2016


The instructions tell you to clean filters after each use. Check the User's Guide for specifics. Quick guide though. Water tank Cap: Under the cap is filter (looks like a screen) remove, clean, replace. Locate the Flow Indicator: turn it counter-clockwise to remove the cap. Lift out the rotor and the filter underneath, Clean and reinstall in reverse order. That should fix the problem. Consumer Care phone number is listed in the User's Guide.

Bissell ProHeat... | Answered on Jan 29, 2016


Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

dfjdg

Bissell ProHeat... | Answered on Dec 27, 2015


then look at the jets they do plug up if not cleaned out after previous use .

Bissell ProHeat... | Answered on Nov 29, 2015


Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

sgsg

Bissell ProHeat... | Answered on Jul 03, 2015


check the belt that drives the brush. Maybe the motor that drives it has quit. Check for power at the head. be careful it's 120 volts

Bissell ProHeat... | Answered on Jan 06, 2015

Not finding what you are looking for?

535 questions posted

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Brad Brown

Level 3 Expert

18108 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bissell Vacuums

  • Bissell Vacuums

Most Popular Question

bissell steam leaner turbo not suction

  • Vacuums
Loading...