HP LASERJET P1006 Printer - Answered Questions & Fixed issues


Use Premium paper. It is a little bit more expensive, but it will reduce the amount of jams that occur

HP LASERJET... | Answered on May 31, 2019 | 197 views


Are you printing Labels or Envelopes?

HP LASERJET... | Answered on May 31, 2019 | 62 views


Check the drivers and see if they are wrong. If so, Change it to HP LaserJet P1006

HP LASERJET... | Answered on May 31, 2019 | 75 views


You need to get it serviced. I have never encountered that problem, but I recommend getting it serviced

HP LASERJET... | Answered on May 31, 2019 | 293 views


I did not know the LaserJet P1006 had upgradable Firmware. I know the newer ones do, but not the LaserJet P1006

HP LASERJET... | Answered on May 31, 2019 | 802 views


Your toner door sensor is broken. I recommend ordering a new one

HP LASERJET... | Answered on May 31, 2019 | 435 views


Clean off the roller. It may not be detecting the paper due to debris on it

HP LASERJET... | Answered on May 31, 2019 | 531 views


Unplug and power off the printer and wait 30 seconds. It will reset the device.

HP LASERJET... | Answered on May 31, 2019 | 581 views


HP LaserJet P1006 is still supported. It can run In Windows 98 though Windows 10. In my answer, I would recommend downloading the Basic Driver. The basic driver allows you to print, manage and doesn't allow anything else to install with it.

Here's the link:

https://support.hp.com/us-en/drivers/selfservice/hp-laserjet-p1006-printer/3435682

Hope This Helps!!!

HP LASERJET... | Answered on May 31, 2019 | 202 views


This may help. Before you disconnected the USB cable did you "disconnect" it using the icon in the system tray? If you did not, try cycling power to the computer with no USB cable for the printer connected. Sometimes when you unplug a USB cable while it is still "connected" to the device your computer will lose track of that USB port. I hope this helps you.

HP LASERJET... | Answered on Nov 13, 2017 | 91 views


you are installing the drivers may be not correct. u remove the printer driver and install the proper driver again otherwise it may be spooler problem then u have to reinstall the os and configure printer dirver

HP LASERJET... | Answered on Apr 07, 2017 | 333 views


To help you troubleshoot the issue paper does not load on the roller, please find the link below:
http://support.hp.com/us-en/document/c02016130

If issue persists, check if printer is under warranty. To check these please find the link given below:
http://support.hp.com/us-en/checkwarranty

If the printer is out of warranty, please contact HP Service Center for servicing the printer:
http://h20566.www2.hp.com/portal/site/hpsc/public/help/contactHP/home?ac.admitted=1459920815636.1123376534.199480143

GuruAid.com

HP LASERJET... | Answered on Apr 06, 2016 | 43 views


MANUAL PRINT IS ALSO KNOWN AS TRAY 1 ON HP PRINTERS. LOAD PAPER INTO THE SLOT ABOVE YOUR PAPER TRAY.

HP LASERJET... | Answered on Dec 14, 2015 | 96 views


I assume that the error is to open the lid of the laser cartridge and check to be torn from the laser sensor has to be a piece of plastic when pressed on the sensor cap ivhizi if the printer should be opened and checked laser

HP LASERJET... | Answered on Dec 08, 2015 | 285 views


Please unplug the printer, wait 2 minutes then plug back in.

HP LASERJET... | Answered on Jul 10, 2015 | 52 views


open toner door pull out the toner ,now remove the paper.

HP LASERJET... | Answered on May 26, 2015 | 32 views


i want hp Laser Jet 1010

HP LASERJET... | Answered on Feb 22, 2014 | 307 views

Not finding what you are looking for?
HP LASERJET P1006 Printer Logo

134 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...