Sharp MX-2700N Color Copier - Answered Questions & Fixed issues


Toner cartridge CRUM error (YELLOW)
CRUM cannot be read or written.

1. Connection trouble or disconnection of the connector and the harness between the PCU and the toner cartridge. Check the connector and the harness between the PCU and the toner cartridge.
2. CRUM trouble. Replace the toner cartridge.
3. Control PWB (PCU) trouble. Replace the PCU PWB.

Sharp MX-2700N... | Answered 3 days ago | 16 views


This procedure may help, it works on older models.
Press # key
press * key
press C key
press * key
enter 16
press start key
Turn the machine off and then back on
Good luck

Sharp MX-2700N... | Answered on Nov 08, 2018 | 4,016 views


It is completely out that is why it is saying replace

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sharp MX-2700N... | Answered on Jan 30, 2016 | 118 views


might be that you are using 3rd party toner or that the machine need to be re calibrate have a tech come out and check it out

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sharp MX-2700N... | Answered on Jan 30, 2016 | 43 views


Run a gradation test, might require a tech to access service mode,

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sharp MX-2700N... | Answered on Jan 30, 2016 | 63 views


Well you could power off the machine disconnect the finsher phyiscally and electrically and then power on the machine

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sharp MX-2700N... | Answered on Jan 30, 2016 | 34 views


what is wrong with you the machine is telling you what is happening then the must be some thing wrong with you grow up ask real question on jokes

Sharp MX-2700N... | Answered on Nov 19, 2015 | 85 views


have you check the sensor actuates on the registration section

Sharp MX-2700N... | Answered on Nov 19, 2015 | 66 views


L4 errors relate to motors. L4-02 specifically means Paper feed motor locking trouble.

You will need to take it in for repairs.

Sharp MX-2700N... | Answered on Nov 05, 2015 | 357 views


Not really a problem, just information.. codes are here:
SHARP MX 2700N MAINTENANCE CODES error codes

Sharp MX-2700N... | Answered on Oct 07, 2015 | 629 views


HI

H5-01 means you have had five consecutive jams, it would suggest there is either something blocking the paper path, or the paper is not being picked up at all.

Try resetting the machine by the following:
Program, *, clear, *

It will then ask for a simulation code, enter 14 and press print, are you sure?, press yes. Clear all, clear all, should reboot the machine and try again.

If it continues to jam, try a different cassette.

Cheers

Andy

Sharp MX-2700N... | Answered on Apr 24, 2015 | 66 views


From the scan section, chose your recipient(s) first.
Then go to Image Settings > Auto/Original >
Choose 2-sided booklet or tablet, choose portrait or landscape orientation. Then scan as usual.

I believe you can also make this a default under System
Settings > [Admin Login] > Image Send Settings

Sharp MX-2700N... | Answered on Apr 10, 2015 | 395 views


You put your papers into the document feeder, then on the LCD screen there is a button that says 2 sided. Touch that button and select what you need. If you have a bunch of single sided pages that you want 2 sided then select 1,1-2. If you have a bunch of double sided pages that you need copied then select 2-2 and then puch the copy button.

Sharp MX-2700N... | Answered on Apr 10, 2015 | 334 views


The simple answer to this question is to perform an image memory clear.

Here is a video on that for newer sharps, from older sharps just press # * C * on the panel, then 66 start, 10 start, execute, yes.



Copier Collin Houston TX Copier and Imaging Expert

Sharp MX-2700N... | Answered on Feb 10, 2015 | 187 views


If you are conecting directly you should be using a usb cable and you will need to install print drivers from sharp usa.

I’m happy to help further over the phone at https://www.6ya.com/expert/ethan_e84416e0b13809d2

Sharp MX-2700N... | Answered on Dec 31, 2014 | 58 views


you want to note the frequency of the ghost image. the drums are 1.5 inch round and the fuser rollers are a little bigger like 2 inch round and then the y1 trans belt is way bigger like 19 inches and the y2 belt is like 6 inches. If th ghost only happends with one color you could be pretty sure your problem is with that single drum. if it happends in multiple colors look at the other options first.

y2 and fuser you can see when opeing the right side of the machine
y2 is the wider rubber belt that is lower and the fuser is the hot hting at the top with that flip down cover.

y1 belt comes out with 4 blue screws after the front and right side of the machine are open, the toner waste container is out, and you line up the u shaped thing in the middle. turn in the direction indicted untill you see the green stick apear in the back threw the u.

The drums come out after you remove the developer units. with the machine off Open the front cover remove the toner waste container and loosen the two blue captured screws on either side of the plastic piece that covers the drum units. once those screws are loose check to make sure that the primary transfer unit is disengaged. there is a u shaped thing in the middle that needs to line up. if it is not lined up then rotate the blue screw in the direction indicated until it is. flip the whole plastic bar up if it catches in the middle don't force it rotate that screw. if it catches on the sides then just push it harder the sides make a pop noise sometimes before they give. each of the developer units have a flip up cover that gives you access to another blue captured screw. Pull on the cover from the bottom up then loosen the screw and the developer units will pull towards you. after you pull a dv unit the corresponding drum unit comes out by pressing a button down. the drum units are rebuildable in this machine. there are two blue plastic screws in the end holding a bronze bushing, and two silver plastic screws holding a cover on. there is a snap on side cover that will release the grid. and then three blue screws to get the wiper out. in general on sharps it is ok to pull out blue screws, but never ever pull out red screws.

Let me know if you need more hlep.

I’m happy to help further over the phone at https://www.6ya.com/expert/ethan_e84416e0b13809d2

Sharp MX-2700N... | Answered on Dec 19, 2014 | 163 views


Where the paper exits the copier into the centre delivery tray there is normally a grey arm about 75mm in length attached to the exit guide fitted to the machine. This very often gets knocked off & is the indicator to tell the machine the centre delivery tray is full. If you look into the centre delivery tray & cannot see a grey arm then this your problem. If you find the arm it attaches to the upper part of the delivery exit guide in the centre. The arm clip has cut outs in it to allow it to only be fitted on one way. The use of a torch would assist greatly.

Sharp MX-2700N... | Answered on Dec 10, 2014 | 55 views

Not finding what you are looking for?
Sharp MX-2700N Color Copier Logo

226 questions posted

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

k24674

Level 3 Expert

8081 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...