20 Most Recent Jandy AQUALINK RS TELELINK KIT Questions & Answers


filter pump must be on and go to devices on you should be able to turn on aquapure make sure 4 pin is connected to aqualink

Jandy AQUALINK... | Answered on Mar 20, 2018


check red 4 pin connector inside top if off or loose or wires touching or wire cut outside if ok bad control board

Jandy AQUALINK... | Answered on Dec 31, 2017


sensor bad or needs cleaning

Jandy AQUALINK... | Answered on Dec 31, 2017


check to see if voltage to relay

Jandy AQUALINK... | Answered on Nov 16, 2017


Need more info. Model and voltage to unit. Is it connected to automation?

Jandy AQUALINK... | Answered on Oct 16, 2017


Look up Zodiac Pool systems, on the web site you can find a list of service providers in your area. You may be looking at replacing your automation at this point.

Jandy AQUALINK... | Answered on May 14, 2017


There is probably a drain valve somewhere near the control panel ... forgetabout it ... too slow.

Best way is to get a small pump and pump it away. Next best is wet dry (shop vac). My favorite is siphon ... dont have to buy anything or drag anything out ... only a hose. By the time my water is out ... I have had time to do the necessary surface cleaning and waxing.

Jandy AQUALINK... | Answered on Jul 13, 2016


check in service if same bad relay if ok check programming

Jandy AQUALINK... | Answered on Jun 11, 2016


see if voltage coming into transformer if ok check transformer for 24 volts ac at back plug of PCB board also check fuse on back of board

Jandy AQUALINK... | Answered on May 01, 2016


if new batteries and it wont come on need new one

Jandy AQUALINK... | Answered on May 01, 2016


check pressure switch should open when pump goes off

Jandy AQUALINK... | Answered on May 01, 2016


check for cut wires or shorted wires at 4 pin red plug

Jandy AQUALINK... | Answered on Apr 29, 2016


clean mode is if you have your cleaner on make sure chemicals are correct super shock and clean fitlers

Jandy AQUALINK... | Answered on Apr 29, 2016


need new PDA

Jandy AQUALINK... | Answered on Apr 29, 2016


if no incoming voltage check feed if voltage coming in check transformer for 24 volts ac at plug on back of PCB board

Jandy AQUALINK... | Answered on Apr 29, 2016


if voltage coming in check transformer if 24 volts at back of PC board need new control board if no voltage replace transformer or check fuse also

Jandy AQUALINK... | Answered on Apr 29, 2016


from factory its 5 if you change you have to open the antenna and turn to learn then turn on PDA and then when it connects turn learn button off

Jandy AQUALINK... | Answered on Apr 29, 2016


go to system set up then change time

Jandy AQUALINK... | Answered on Apr 25, 2016


check spa side remote disconnect if it quits replace remote

Jandy AQUALINK... | Answered on Apr 25, 2016


put aqualink in sevice till you get another one

Jandy AQUALINK... | Answered on Apr 25, 2016

Not finding what you are looking for?
Jandy AQUALINK RS TELELINK KIT  Logo

179 questions posted

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10321 Answers

Bill Jordan

Level 2 Expert

373 Answers

Anthony Davis
Anthony Davis

Level 1 Expert

61 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jandy Pool & Spa

  • Jandy Pool & Spa

Most Popular Question

water temp keeps showing 197 or higher

  • Pool & Spa
Loading...