20 Most Recent Weiser Lock POWERBOLT ELEC DEADBOLT - Page 6 Questions & Answers


I found this Frequently Asked Questions sheet for the Powerbolt 1000:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

I hope this helps.

Weiser Lock... | Answered on Mar 05, 2011


Here is a link to the installation instructions, which includes programming:

http://www.weiserlock.com/PDFs/install_sheets/pb_eng_install.pdf

Weiser Lock... | Answered on Mar 05, 2011


Here is a link to the Weiser website and the page that explains it.
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

Weiser Lock... | Answered on Jan 25, 2011


Here's a free manual you can print out with complete installation and programming instructions you can keep for addressing any other concerns you might have in the future.

I thought this might be easier for you to work from, since you want to reset your master code which will clear any other codes as well. You can then enter in all new codes to operate your lock.
It is easy and straight forward to program and use.

http://www.smarthomeusa.com/Products/ED1460XXXX/manuals/WeiserLockPowerbolt1000-manual.pdf

Hope you find this Very Helpful - Best regards!

Weiser Lock... | Answered on Jan 09, 2011


Pull down and then out at the bottom of the cover. See http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx
Underneath is instructions on how to set the code.

Weiser Lock... | Answered on Dec 26, 2010


change the door direction jumper as outlined in this article - http://www.weiserlock.com/Support/Faq/50160000000HhmZAAS.aspx

Weiser Lock... | Answered on Dec 26, 2010


Are your batteries fresh?
also a strong magnetic feild near the lock assembly can erase the code.

Weiser Lock... | Answered on Dec 19, 2010


remove all batteries, wait about 10 seconds then install new ones, one at a time, I found this clears the flashing

Weiser Lock... | Answered on Nov 19, 2010


Mine did that too for a month. Make sure all the batteries are new alkaline batteries of the same brand, and remove them for a few minutes (if already installed) and replace them in the unit. I reset my code as well afterword. Did the trick for me.

Weiser Lock... | Answered on Oct 06, 2010


Take off the cover on the inside door of the lock. Grip it on the sides and pull up or twist. Press the Program button (on the left of the power board) once. Then type in desired code (4-8 digits) on the Touchpad followed by pressing the Lock button. If you hear a 2-second beep, the code is properly stored. If you don't hear the beep, the encoding period timed out. Then you need to repeat the sequence from pressing the Program button but do it faster. To store a second code, press the Program button twice and then type in the desired code followed by the Lock button. (Any earlier code will be lost during these steps.) Then replace the cover over the power board.

If you want to print out the programming information, go here: http://www.weiserlock.com/en/products/smartseries/powerbolt.aspx and scroll down to the Installation instructions. The programming instructions are at Step 5 on the PDF.

I hope this helps.

Cindy Wells

Weiser Lock... | Answered on Jul 23, 2010


The main control board in you lock has gone bad and needs replaced.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

Weiser Lock... | Answered on Jul 22, 2010


changed the battery and lost the manual, put my code in and it worked , latter it started to beep and now it doesn't work... respond at all ....help thanks

Weiser Lock... | Answered on Jun 02, 2010


if the batteries are new and good, sounds like a problem with the lock motor..is it a new unit? if so exchange it. try another set of batteries.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

Weiser Lock... | Answered on Feb 06, 2010


Batteries, when they are cold, do not give off the same amount of power. You can test this by putting them in a freezer for a few hours and then trying them in a battery operated device. They cold does not hurt them, and they will work fine once they warm up. Depending on how cold the batteries get for your deadbolt this could be the problem. Also if the deadbolt is rubbing at all against the lock plate it could put unnecessary pressure on the motor. Schlage does make a deadbolt system that uses a keypad and a manual turn. The Camelot or Plymouth models.

Weiser Lock... | Answered on Dec 16, 2009


Lock continues to beep. part no. 70-005087 new batteries, lock is 10 years old.

Weiser Lock... | Answered on Dec 03, 2009


open the cover, move the jumper over.

Weiser Lock... | Answered on Dec 02, 2009


The "program button" is behind the panel on the indoor side of the lock. See instructions below.5a64943.jpg

Weiser Lock... | Answered on Nov 20, 2009


  • Take out batteries and unplug powerstrip.
  • Let it sit for 1 minute, then put the batteries back in and wait another minute.
I contacted customer support... they tell me the FAQ information on their own website is incorrect. The opposite is true, therefore the following is correct:
  • If it does not beep, the powerboard needs to be replaced
  • If the unit continues to beep, the keypad needs to be replaced
Here in Canada, they will send you a new one within 3-5 days free of charge. Call customer support:

Canada: 800-501-9471
US: 800-677-LOCK


The woman was very friendly. Great customer support!

-=dån=-

Weiser Lock... | Answered on Sep 14, 2009

Not finding what you are looking for?
Weiser Lock POWERBOLT ELEC DEADBOLT Logo

149 questions posted

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Azam Ali

Level 1 Expert

31 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

6032 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Weiser Lock Locks & Locksmithing

  • Weiser Lock Locks & Locksmithing

Most Popular Question

need change code

  • Locks & Locksmithing
Loading...