Question about Krups Small Appliances Espresso Machine

1 Answer

Krups 7240 ground coffee not ejected

We have a 10month old machine and lately its making weak coffee and it sounds as though the grinding mechanism is struggling, add to this its not ejecting coffee grounds into the side container.
we just took every possible removable part off the machine and shook it a little and old grounds came out, but not many, add to this we are getting grounds in the drip tray and water in the container that is meant to catch grounds.  We are thinking that somehwere along the line steam or similar got in the machine where it shouldnt be?  its currently drying out and we are then rinsing and doing another clean..
fingers crossed, i really dont want to go searching for the reciept.  And i want my coffee in the morning!
Any suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Krups Master
  • 1,355 Answers

The best thing you can do is find the receipt and exercise the guarantee. The problem you have is not a simple fix.

Posted on Mar 24, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Krups Orchestro 889

the o ring of the upper and lower pistons should be replaced

Posted on Aug 10, 2008

  • 1 Answer

SOURCE: Krups XP7240 leaks

The grind selector knob can be removed with the following steps: 1) Remove screw on side near grinder (do not let the screw fall into grinder, :-) ), 2) use sharp knife or similar to pry off cover with three dots. This should be easy. 3) Now you can rotate the grind selector and see that the white clear plastic does not rotate and the black does. There are two little pieces (one black, one clear plastic) on opposite side from grinder that slide over eavh other to keep this knob 'locked' into place. 4) again with a sharp pointed knife or similar you can separate these two pieces to 'unlock' them. This is made easier by lifting the side of the bean holder by the grinder gently and tipping it up. Be careful not to force anything too much. The black part should pop off. 5) Now you can lift off the clear bean holder.

After this good luck. We made it farther into the machine, but could never get to where we needed to go to fix our problem.

Krups must be congratulated for designing a machine that cannot be repaired and must be replaced with new purchases.

Posted on Jan 11, 2009

  • 1 Answer

SOURCE: Water steams away and nothing drips into the caraffe

I had this problem too and finally found a fix for it.

I don't know if the cause of this issue is the same for everyone experiencing the problem, but the issue for me was hard water. The fix is to run vinegar mixed with water through the machine quite a few times, until it starts to run normally.

If you do have hard water issues, it's recommended that you run vinegar or citric acid through the machine about once a month, to keep deposits from building up.

Posted on Jan 27, 2009

  • 1 Answer

SOURCE: i need a manual for krups xp 7240, krups xp 7200, krups xp 7230

I have the manual, send an email to me at inouside@hotmail.com and I will reply to you with the manual in pdf format.

Posted on May 14, 2009

  • 14 Answers

SOURCE: krups xp 7240 cofee machine

6
Pump in actuator down phase


The flow has not dropped (> 50ml/min)
after the actuator has been filled to the
maximum (80ml); there is a water
leakage and the actuator does not fill
Look for the leakage source:
hoses, actuator, priming valve?
Switch or distributor switch
control fault: incorrect detection
of cams  error in distributor
position in cylinder descent
phase.
Flowmeter hoses changed over
Distributor problem (leakage at
drain ..)
Faulty connection between the
2 picto boards
If no leak detected, replace
power board V26 with V29

Posted on Jul 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hello, i have a krups xp7220 and i have two problems with her.


A common place for a leak under the machine is the barista seal that goes in the bottom of the boiler around that eject rod. Barista seal part number is MS5002202, Seals on the tamping piston are MS5002040 (there can be 1 or 2 of these piston seals) If fixing the leaks does not fix error 6 then I expect it will end up being the distributor. Part number MS2A01500

Jun 17, 2017 | Krups Coffee Makers & Espresso Machines

2 Answers

Why does it brew weak coffee?


can depends many factors, try to grind finer coffe powder and warm well the machine before starting to brew coffee. If the grinder does not make finer coffe powder then you must contact the service, check if blades are in place before calling them...

Jan 19, 2016 | Saeco Vienna SuperAutomatica Coffee...

1 Answer

Coffee scraper arm sticking


You will need to remove the brewing unit from the base and tip it upside down to inspect/free up the mechanism. While you have it that far replace the seal (barista seal) at the bottom of the brewing chamber that seals the rod on the ejector mechanism. Also inspect the back of that sweeping arm where it runs in a track at the back of the tamping piston ram. A new tamping piston with seals and tank seal would not go astray, all the parts are relatively cheap NZ$40 easily gets the lot.

May 19, 2014 | Bialetti Mokona Espresso Machine

1 Answer

Krups XP 7220 makes coffee but will not Eject the pellet of used coffee grounds. It makes a loud bang. Have discontinued use promptly. Any suggestions on dismantling, from above or below? Thanks in...


There is an arm that drops back into place just before the plunger drops to pack the grounds. After the espresso is pulled the plunger comes back up and the arm moves forward and swipes the pellet into the pellet container. My thought is that the arm has come out of sync or become disconnected. The sound you are hearing could be the mechanism trying to push the arm forward but snapping off.
As for disassembling, there are directions dismantling the unit on other posts here (for 7240 or 7230), but the one thing that wasn't so clear to me is that the front facade isn't secured with any screws, but rather hooks that are part of the molded construction of the facing. Once you pull up on the facade about a half an inch, it should pop off. You can see some of the six hooks in the pic below.palibaacsi.jpg

May 10, 2011 | Krups XP7230 Compact Super Automatic...

1 Answer

Krups 4000 coffee machine wont make strong coffee


Maybe the grind is too fine and it is building up too much back pressure. Max is normally around 15 bar, more than that and the pump stops functioning. Also try another silver bucket that holds the grounds, if it is double walled sometimes grinds too small can block them between the skins. There was often a single wall bucket available that eliminated the blockage problem.

Jan 25, 2018 | Krups XP 4000 Espresso Machine

3 Answers

Error code 07 on my Krups XP 7220 coffee machine


Error code 07 on my Krups XP 7220 coffee machine what to do? Nick

Oct 26, 2009 | Krups Small Appliances Espresso Machine

2 Answers

I need a manual for krups xp 7240, krups xp 7200, krups xp 7230


I have the manual, send an email to me at inouside@hotmail.com and I will reply to you with the manual in pdf format.

Mar 04, 2009 | Krups XP7230 Compact Super Automatic...

1 Answer

Krups xp7420 espresseria automatic


am o proare 01 la un espesor krups 7220/7240

May 11, 2008 | Krups Coffee Makers & Espresso Machines

1 Answer

Krups Orchestro Dialog coffee machine


that mean no coffee go through us if you dont use the machine often you might have coffee residue on the grinder teet remove the coffee bean in the hole were the coffee bean goes use a brush and clean the grinder teet very good with the residue of coffee gonna grind and gonna go through thanks for usig fixya pierre

Feb 07, 2008 | Krups Orchestro Dialog FNF2 Espresso...

Not finding what you are looking for?
Krups Small Appliances Espresso Machine Logo

Related Topics:

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Ray Murphy

Level 2 Expert

68 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...