Question about Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Open Question

Bissel brush stops turning when it come it contact with floor

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 432 Answers

SOURCE: Bissell Velocity Vacuum brushes stopped

The brush bearings wear out on these things. I know I replaced mine twice before buying new carpet. I've had it for 10 years,
You can order these parts on the Bissell website:
http://www.bissell.com/Products/p/CleanView+Brush/product.aspx
http://www.bissell.com/Products/ak/replacementparts/p/CVPT+II/product.aspx?%23=Detail#Detail
http://www.bissell.com/images/UserGuides/35934_804.pdf

Posted on Mar 30, 2008

Ad

Anonymous

  • 38 Answers

SOURCE: Bissell Momentum roller brush doesn't roll w/ pressure

This is going to sound funny, but check the wheels. Sounds like the pin or shaft that holds them is broke. Also check the tension on your belt. If the tension is to loose then the brush will have a hard time spinning.Good luck

Posted on Jul 26, 2009

Anonymous

  • 36 Answers

SOURCE: I have a Bissell Pro Heat 2X carpet cleaner and

The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch.

Posted on Jul 31, 2009

Anonymous

  • 10 Answers

SOURCE: will spray from handtool but not from brush floor

Thanks to many others who have posted on similar problems -- water and/or solution sprays through the handheld tools, but not through the main machine.

As others have suggested, I removed the water reservoir, which exposes the 2 main water sprays mounted above the rollers. Using, pliers, I carefully slid the clips back. Gently but firmly removed the two red nozzles.

Elsewhere I have read suggestions to just do one nozzle at a time. However, I found out that if you remove both red nozzles, you can then blow through one side and it will come out the other. In my case, that dislodged a nice collection of crystal-like chunks (guessing it may be crystallized residue from the cleaning solution).

There was also a bit of blockage in one of the red nozzles, which I cleaned out. Make sure you can blow through both of them with little resistance.

Reassemble: Push red nozzles back into hoses. Using pliers, reposition sprung clip back over the red nozzle. Snap nozzles back into place. Refill tanks and power it up.

In my case, that resolved the problem of no sprays from the main machine. Sprays like new now. Hope yours does too!! e

Posted on Sep 26, 2009

Vac Belts

Vac Belts

  • 701 Answers

SOURCE: I have a 3760 lift off bissell. Replace the torn

Did you get the right belt size? The belt you should have bought is this one:

Bissell 3760 Belt

Posted on Nov 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bissell 3522 can use to wooden hard floor


Hi Marian. Thanks for asking this question. The Powerforce vacuum has a bare floor setting; however, you may want to contact the hard floor manufacturer for their recommendation regarding the use of a rotating brush.

Aug 12, 2013 | Bissell 3522 PowerForce Bagged Upright...

1 Answer

Is the beater brush on the Bissell Helix NOT to spin on bare floor setting?


Hey Tony! The brush does continue to rotate when using the vacuum on the bare floor setting.

Feb 02, 2013 | Bissell Cleanview Helix Deluxe Bagless...

1 Answer

Brush roller not spinning. belt, spindle okay. roller taken out and cleaned, no thread. replaced but no dice. ???


Use only BISSELL Style 10 Replacement Belts (#32074) in your BISSELL PowerForce Bagless.
  1. Unplug cleaner from electrical outlet.
  2. With Rotating Floor Brush removed from vacuum cleaner, grasp old Drive Belt and remove from Motor Pulley. Discard old Drive Belt.
  3. Place new Drive Belt over Motor Pulley and stretch other end over Rotating Floor Brush in the space between the bristles.
  4. Place ends of Rotating Floor Brush down into slots on sides as shown.
  5. Turn Rotating Floor Brush by hand several times in the direction of Motor Pulley. If properly installed, Drive Belt will center itself on Rotating Brush.
  6. Reposition Brush Cover and snap back into place. Check to be sure all three latches are secured.
  7. When you turn on the vacuum, do you see the motor that spins the belt spinning at the bottom? If not, it sounds like you may have a burned out motor.
If suggested solutions do not correct the problem, call:
BISSELL Consumer Services 1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Jun 01, 2011 | Bissell 6594 PowerForce Bagless Upright...

1 Answer

I have a 3760 lift off bissell. Replace the torn


Did you get the right belt size? The belt you should have bought is this one:

Bissell 3760 Belt

Nov 08, 2009 | Bissell LiftOff Revolution Pet Vac 37602...

1 Answer

Bissell Momentum roller brush doesn't roll w/ pressure


This is going to sound funny, but check the wheels. Sounds like the pin or shaft that holds them is broke. Also check the tension on your belt. If the tension is to loose then the brush will have a hard time spinning.Good luck

Jul 26, 2009 | Bissell Vacuum - Momentum Cyclonic 1 ea...

1 Answer

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are...


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch.

Jul 14, 2009 | Bissell Carpet Cleaner Powerbrush Deep...

1 Answer

Rotating Floor Brush Isin't spinning


It appears that the end of the brush is getting jammed with hairs, treads, and/or dust or the belt may be worn. Try taking the brush out and hold it by the ends and try to turn it. It should turn quite easily if it is working good. If not try taking the ends off and clean them out. Also, make sure the belt is good.

Mar 19, 2009 | Bissell Upright Vacuum - The Pet Hair...

1 Answer

Bissell Velocity Vacuum brushes stopped


The brush bearings wear out on these things. I know I replaced mine twice before buying new carpet. I've had it for 10 years,
You can order these parts on the Bissell website:
http://www.bissell.com/Products/p/CleanView+Brush/product.aspx
http://www.bissell.com/Products/ak/replacementparts/p/CVPT+II/product.aspx?%23=Detail#Detail
http://www.bissell.com/images/UserGuides/35934_804.pdf

Mar 29, 2008 | Bissell 3594 CleanView PowerTrak Bagless...

Not finding what you are looking for?
Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Brad Brown

Level 3 Expert

18110 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...