Question about HP DeskJet 722c InkJet Printer

1 Answer

Printer stopped printing and says its off line!

How do I get it back on line?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 731 Answers

HI,

Im Rizwan from India, i would to tell u to check few things that will resolve this problem

SOLUTION:

NO 1: Check the Connection and power
1.Check the USB cable and the power line to the printer.
2.unplug and replug the cables at the PC an printer end.

NO 2:Check the printer status in control panel.
1.Click start - >Run.
2.In the run window type "control" (without quotes).control panel will open.
3.In the control panel, look for printers and fax and check the printer icon.
4.If printer icon says Offline, Right click on printer icon and select "use printer online"
5.Try printing, if it didnt print follow step NO 3.

NO 3:Restart the USB Composite Device.
1.Right click on MY computer ->Properties->Hardware->Device manager.
2.You will get Device manager window popping out.
3.Scroll down to "Universal Serial BUS controllers".Click on the (+) sign.
4.Check for the "USB Composite Device" and right click on it, click Uninstall.(IMPORTANT NOTE:WE HAVE TO UNINSTALL THE PRINTER'S USB COMPOSITE DEVICE, TO KNOW WHETHER IS THE PRINTER'S USB COMPOSITE DEVICE, RIGHT CLICK ON USB COMPOSITE DEVICE AND PROPERTIES,look for wat location says, Eg -LOCATION : HP DESKJET 720C
5.Disconnect the USB and reboot the PC.
6.Connect the USB after reboot, you will get popup "Found new hardware".Then the Drivers will be installed Automatically.

Try printing Now, if it didnt work please response.

Thank you
Rizwan
rizwan84tx@gmail.com

Posted on Dec 06, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a jd280 loader on my jd4640 tractor, it is a self-leveling loader. There is a bleed back line coming off the self-leveling valve , I do not know where to connect it. Any help is appreciated


bleed back lines normally do not have pressure as they are just that bleed valves /lines . Hold the line in a tin and check when it works. I would suspect that the line should go back to the reservoir

Dec 25, 2014 | Cars & Trucks

1 Answer

Fuel want pull into bulb on my craftsman 27cc weedwacker #711200


There are 2 fuel lines going into the back of the primer bulb. One line goes from the back of the bulb into the fuel tank, and the other goes from the back of the bulb into the carburetor. I believe that the line that goes into the fuel tank has disconnected from the back of the bulb. You will need to remove the bulb, find the line that dropped off of the bulb and into the tank, and reconnect the line to the back of the bulb.

Jul 28, 2014 | Craftsman 27cc 2 Cycle Crank Straight...

1 Answer

Replace water line in fridge


The line going into the dispenser is a 5/16 line. You'll have to remove the front of the dispenser on the door to get access to the line to unclip it. Once you have that done you can pull the line out from the bottom. At this point there are a variety of different unions, compression fittings, etc. to splice the line. After that you just feed the line back through the bottom of the door, clip it back in place, put the dispenser back together and your done.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

May 31, 2012 | Frigidaire Refrigerators

1 Answer

Replace door water dispenser plastic tubing


The line going into the dispenser is a 5/16 line. You'll have to remove the front of the dispenser on the door to get access to the line to unclip it. Once you have that done you can pull the line out from the bottom. At this point there are a variety of different unions, compression fittings, etc. to splice the line. After that you just feed the line back through the bottom of the door, clip it back in place, put the dispenser back together and your done.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

May 30, 2012 | Kenmore Side by Side Refrigerator

1 Answer

I have a Poulan Pro leaf blower/vac. The fuel lines cracked inside the gas tank so I pulled them out & bought new ones. Now i can't get them back in to the gas tank. I understand there are


Make sure that you have the right size lines the smaller diameter line goes into the bottom hole of the tank cut a 45 angle at the end of the line as you put the line into the tank twist and push until you get enough line to pull up through the fuel filler hole then cut the line so that the 45 is no longer and slip the fuel filter on then pull back the line until the filter rests at the bottom of the tank. Do the same with the upper line except that line will only go in 3 to 4 inches. I hope this helps you.

Feb 29, 2012 | Poulan Pro Gas BlowerVacuum ()

1 Answer

Replacing a timming belt where are the marks suspost to line up


You didn't get the timing marks lined up between the cam and the valves. You are going to have to open it back up and line the marks back up correctly. Make sure you get the Number 1 cylinder lined up to Top Dead Center on the compression stroke and have the valves lined up correctly then line the timing marks up on the timing gears.

Jun 24, 2010 | 1992 Mitsubishi 3000GT

1 Answer

Replacing rediator..hose on bottom tranny line how does it disconect from radiator


if im not mistaken there should be a plastic ring around the line..if so pull it back and there will be a little c clip on the line ..pull it out...dont lose it tho and then pull out line...then put c clip back in the slot then push the line back in.

Mar 05, 2010 | 1999 Dodge Ram

1 Answer

Cannot print. Message says the printer is off-line. How do I get back on-line? Thanks


Try turning the power off and then back on after a few seconds.  If that does not work go to the Printer Control Panel or Printer Utility file and see if it needs to be set up again.  There may be a selection there to bring it back on line.

May 20, 2009 | Office Equipment & Supplies

1 Answer

U-line BI98 water line leak


Take off the back panel, the water line plugs in from the back. The icemaker has mounting screws, but there's a thermal mastic that kind of glues it to the evaporator. You don;t need to remove the icemaker to change the water line, I would put the screws back in and leave it. Don't force the icemaker from the evaporator, it might damage the evaporator.

call 1-800-779-2747

OnlineService@U-Line.com

http://www.u-lineservice.com

Mar 29, 2008 | U-Line Icemaker

Not finding what you are looking for?
HP DeskJet 722c InkJet Printer Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...