Question about Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

Deleting Codes on a Weiser powerbolt.

When I program a new code into our Weiser Powerbolt, the old codes do not get cancelled. How do I cancel all old security codes and start fresh?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 963 Answers

The Weiser brand and Kwikset brand Powerbolt are identical (Black & Decker), so these instructions will work just fine for you:

http://www.kwikset.com/Customer-Support/Product-FAQs/Faq/50160000000HhhEAAS.aspx

Notice that the above is a .PDF file type. That means that you need to have Adobe Reader or similar installed on your computer to view it. So if you are unable to view the file, download (for free) and install Adobe Reader first. You can get it here:

http://get.adobe.com/reader/

Posted on Jul 11, 2012

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 26 Answers

SOURCE: my powerbolt keeps beeping short beeps and then

dead batteries

Posted on Aug 18, 2009

sonicboomele
  • 1557 Answers

SOURCE: How do I reprogram the

  • Remove the inner cover plate from the lock.
  • Locate the small round reset button near the left side of the circuit board (Red or Black).
  • To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
  • To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.
best of luck.

Posted on Aug 02, 2010

  • 963 Answers

SOURCE: How do I clear (erase) all codes from my Weiser

How do I change the access code (and delete my old code) on my Powerbolt 1000?
The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.

pb1000programbutton.jpg

  1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.
  2. Press the PROGRAM button twice, enter the same new code and then press the LOCK button once.
  3. Press the PROGRAM button three times, enter the same new code and then press LOCK once.

If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour. After the hour has passed, you may re-enter the batteries.



United States of America Customer Service Contact Information
Call Us Toll Free: 800-422-4278 (Mon-Fri, 6:00am - 4:30pm PST)


http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

Good luck, Elizabeth!


Posted on Jul 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset new codes and old existing codes won't erase,the original code from last year still works, even after installing 2 new codes


Here's the link to the online instructions:
http://www.weiserlock.com/PDFS/instructions/Electronics/Powerbolt.pdf
Programming instructions are on page 6. Notice that allowing too much time between inputs will be a problem.
If you cannot successfully override your existing codes, contact Weiserlock Customer service:
http://www.weiserlock.com/CustomerService/ProductSupport/SupportContact.aspx
A note about PDF files: You will need adobe Reader or equivalent installed if you are unable to view the instructions. http://get.adobe.com/reader/
Good luck!

Nov 03, 2011 | Weiser Lock POWERBOLT ELEC DEADBOLT

2 Answers

We bought a house with this lock and don't know how to cancel the previous code and start a new one. We don't know how many digits to put in for the code.


To change your code:

1. Remove the inner cover plate from the lock.

2. Locate the small round reset button near the left side of the circuit board (Red or Black).

3. To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

4. To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.


hope this helps

John

Sep 16, 2011 | Weiser Lock Powerbolt 1000 Lock

1 Answer

How to key in code


This link will take you to the installation & programming instructions (on page 6) for the Kwikset Powerbolt, which is exactly the same as the Weiser Powerbolt:


http://s7d5.scene7.com/is/content/BDHHI/40486-02

Good luck!

Jul 31, 2011 | Weiser Lock GED1460X GED1460X15A Antique...

1 Answer

How do I clear (erase) all codes from my Weiser Powerbolt 1000 in order to start with fresh entries? Adding new codes does NOT override/delete old existing codes as page 7 of my manual indicates. I now...


How do I change the access code (and delete my old code) on my Powerbolt 1000?
The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.

pb1000programbutton.jpg

  1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.
  2. Press the PROGRAM button twice, enter the same new code and then press the LOCK button once.
  3. Press the PROGRAM button three times, enter the same new code and then press LOCK once.

If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour. After the hour has passed, you may re-enter the batteries.



United States of America Customer Service Contact Information
Call Us Toll Free: 800-422-4278 (Mon-Fri, 6:00am - 4:30pm PST)


http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

Good luck, Elizabeth!


Jul 26, 2011 | Weiser Lock Powerbolt 1000 Lock

1 Answer

I need to reset the code


How do I change the access code (and delete my old code) on my Powerbolt 1000?
The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.

pb1000programbutton.jpg

  1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.
  2. Press the PROGRAM button twice, enter the same new code and then press the LOCK button once.
  3. Press the PROGRAM button three times, enter the same new code and then press LOCK once.
If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour. After the hour has passed, you may re-enter the batteries.

Jun 22, 2011 | Weiser Lock GED1460X3BR Lifetime Polished...

1 Answer

How do you reset all the codes on a weiser lock?


Here's a link to the Frequently Asked Questions page for the Powerbolt 1000:

http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

The instructions for reprogramming the code can be found there. Good luck!!

Oct 29, 2010 | Weiser Lock Powerbolt 1000 Lock

1 Answer

How do i program 2 differt codes and erase old codes


Here's a link to the Frequently Asked Questions page for the Powerbolt 1000:

http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

The instructions for reprogramming the code can be found there.  Good luck!!

Oct 26, 2010 | Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

How do you cancel existing codes?


The codes should be overwritten when you program in a new code.

Here's a link to the Frequently Asked Questions page for the Powerbolt 1000:

http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

The instructions for reprogramming the code can be found there. Good luck!!

Aug 09, 2010 | Weiser Lock Powerbolt 1000 Lock

2 Answers

Our Powerbolt 1000 will not delete old codes.


Are you certain you're programming new codes properly? It should just overwrite the codes when new ones are programmed. If you are doing it right, then I'd say you may want to have the unit repaired/replaced...
To program new codes (just in case):
Push the program button on the control board once for memory 1 OR twice for memory 2. Enter a 4-8 digit code. Push the lock button to end the entry. The unit will emit a 2-second long beep if your code is accepted. (If it doesn't beep, you were too slow. Try again.) Repeat the process for the other memory position.

Jan 30, 2010 | Weiser Lock Powerbolt 1000 Lock

1 Answer

After changing the code, it will not delete the old ones. how do you do that?


Be sure to change both codes. Press "program", then the code, then the lock button. Then press "program" twice, then a second code, then the lock button.

Nov 30, 2009 | Weiser Lock Powerbolt 1000 Lock

Not finding what you are looking for?
Weiser Lock POWERBOLT ELEC DEADBOLT Logo

977 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Azam Ali

Level 1 Expert

31 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

6026 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...