Question about Frigidaire Ovens

1 Answer

Frigidaire model FEF352CATB has a F3 error code

Model #: FEF352CATB has a F3 error code when I turn the oven on in any way possible. I checked the resistance of the thermocouple for the oven and it was 1060 ohms. Manual said 1100 @ room temp so....

Posted by on

Ad

1 Answer

  • Official Brand Answer
  • 4,342 Answers

Hi - Typically error code F3 indicates a faulty sensor probe or wiring harness between sensor probe and EOC. Try resetting the range by unplugging it or flipping the circuit breaker off for two minutes (this usually will clear most false error codes). Turn on the range and if resetting the unit proves to be ineffective, I would recommend contacting a professional to move forward accurately.

Posted on Oct 16, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: I have an identical problem with a FEF352CATB.

There is a possiblity the oven thermostat may have to be repaired or replaced

Posted on Sep 02, 2009

  • 338 Answers

SOURCE: Error F3 on display ovens beeps

the temperature probr is located inside your oven in one of the upper corners. it should be a round stick looking piece. some are removed from the front others are removed from the back.

Posted on Nov 26, 2008

  • 87 Answers

SOURCE: F2 Error but Sensor Checks at 1100 ohms

Order a new sensor.

Posted on Jun 08, 2007

  • 1 Answer

SOURCE: GE Model JTP15 oven shows F3 error code

I have the same problem. I noticed that the oven gets to the selected temp ok. Then when the pilot attempts to RELIGHT, it gets the error F3. Did you get a solution? After other posts, I will see if the temp sensor is around 1100 ohm as suggested by others. Ken

Posted on Sep 24, 2007

oldTech2332
  • 2341 Answers

SOURCE: My oven displayed F5 then

Hello,

When checking the sensor it shouls be checked at room temp (even if power off) at it should be between 1060-1100 ohms at room tempature. 16 ohms the new sensor is shorted the F2/F3/F4 all relate a faided sensor and the F5 error code says the clock (electronic oven control) is defective.

Test the sensor again at room temp...if only 16ohms its no good and will throw the F4 code everytime again a good sensor measured at room temp should be between 1060-1100 ohms


GENE

Posted on Sep 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Frigidaire fault code F3


Within my research I was able to locate code "F3" which indicates a possible error with the oven probe. It is recommended that a Service Specialist assist you with further diagnosing the issues.

Jan 05, 2013 | Frigidaire 30" Self-Cleaning Freestanding...

Tip

Whirlpool oven, stove and range fault codes (ERC and EOC display errors).


Here a list of Whirpool oven fault codes. The codes had been collected from different service manuals. This was a memo that I wrote for my own use. I think this can be useful to owners and technicians.

WHIRLPOOL - most models
Range/Stove and Oven Fault Codes, Common error codes.

F1 - Analog control board Failure
Disconnect for one minute - if error comes back, replace control board
F1 - Shorted control keypad
Replace keypad
F3 - Oven temperature sensor open
Replace oven temperature probe
F2 - Oven temperature sensor shorted
Replace oven temperature probe
F3 - Oven too hot
Replace oven temperature probe
F3 - Clean temperature too hot
Replace oven probe
F5 - Door latch switch fault
Test and replace the door switch.


Whirlpool with 4 Digit Failure Code:

F1 - E1 - Electronic control (flip flop)
Replace control board
F2 - E0 - Shorted control keypad
Replace keypad
F3 - E0 - Oven temperature probe open
Replace temperature probe
F3 - E1 - Oven temperature probe shorted
Replace temperature probe
F3 - E2 - Oven temp too high
Replace temperature probe
F3 - E3 - Clean temp too hot
Replace temp. probe
F5 - E0 - Check door latch
F5 - E1 - Check door latch
Replace switch if defective

WHIRLPOOL Polara models 5 digit codes:

F1 F0 - EEPROM communication error
Replace ERC
F1 E1 - EEPROM checksum error
Replace ERC
F1 E2:7 - UL A/D errors
Replace ERC
F1 E4:2 - Model ID error
Reinsert keytail.
F1 E6:0 - Latch signal mismatch error
Replace ERC
F2 E0:4 - Shorted key error
Replace keypad assembly
F2 E1:3 Keytail unplugged
reinsert the keytail
F3 E0:5 Top oven sensor open
Test and replace top probe.
F3 E1:6 Top oven shorted
Test and replace temp probe
F3 E2:9 Bake range over temperature
Test and replace temp probe
F3 E3:8 Clean range over temperature
Test and replace temp probe.
F3 E4:10 Bottom oven sensor open
Test and replace temp probe
F3 E:15 Bottom oven sensor shorted
Test and replace temp probe
F5 E0:14 Door switch errot
Test and eventually replace door lock switch
F5 E1:16 Door latch not operating
Test and eventually replace door latch
F8 E0:17 Refrigeration error
Test the cooling module.
PF Power failure - Does not indicate a fault.
PF occurs when power is disconnected.

WHIRLPOOL
Models SF3, 30'' and 24"

F2 - Oven temperature above specifications
Check 8-pin connector from temp. probe to Electronic Oven Control
F3 - Open oven temperature probe failure
Check wiring, replace oven probe if necessary
F4 - Shorted oven temperature sensor failure
Check wiring harness, replace oven temperature probe if necessary
F5 - Push button stuck or faulty
Check for binding of pushbuttons and control panel glass. If OK, replace touch panel
F6 - Electronic control logic error (timing)
Replace Electronic Range Control (ERC)
F7 - Electronic control logic error (lock motor)
Replace ERC.
F8 - Electronic control logic error
Replace ERC.

on Jan 31, 2010 | Whirlpool RBS305PDS Electric Single Oven

1 Answer

My frigerdaire oven heats for a while about 15-30 minutes then shuts down with a beeping noise and a f3 code.


Good Afternoon Friend,

I see that your Frigidaire double oven heats up for about 15-30 minutes, then shuts down and begins beeping while showing an F3error code. The F3 states that the oven is sensing a potential runaway temperature. This is possibly a sensor issue or it could be a false error code.

I suggest giving your double oven a hard reset by cutting the power at the circuit breaker for at least 2-3 minutes.

After restoring power you will need to reset the clock. You will do this by entering in the time and pressing start.

Let the oven heat up, and if you are still receiving an F3 error code, I suggest either contacting the manufacturer or contacting your local authorized technician to diagnose your appliance. Hope this helps.

-Best Regards-
WP

Jan 27, 2012 | Frigidaire 30 in. Electric Gallery Series...

1 Answer

My fridgidaire oven shows a f3 error code


F3 Open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

Nov 06, 2010 | Frigidaire Ovens

1 Answer

I have an identical problem with a FEF352CATB.


There is a possiblity the oven thermostat may have to be repaired or replaced

Sep 01, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Kenmore Oven


F3 Oven temperature sensor open Check oven temperature sensor, should be ~1100 ohms at room temperature. If too high or low, replace oven temperature sensor

Jul 13, 2009 | Frigidaire GLEB27S7A Electric Single Oven

1 Answer

F3 message displayed


HI, you oven temp sensor if malfunctioning. the circuit is open. its basically dead. Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

May 22, 2009 | Frigidaire 24" Built-in Single Electric...

1 Answer

Range Cleaning Cycle not Working


All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Feb 22, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

F2 and F3 code appearing along with annoying beeping


i think f3 error code has something to do with the temp probe maybe it is the problem. the temp probe is located if you open the door directly in the back wall. it looks like a prong. should read 1100ohms the f2 error code though usually has something to do with the keypad i would check all the connections maybe they are loose.

Jan 04, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

Not finding what you are looking for?
Ovens Logo

Related Topics:

1,281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Ovens Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Bruce Denton

Level 2 Expert

273 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Frigidaire Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...