Question about Maytag Legacy Series Top Load Washer

1 Answer

Maytag legacy series washer not holding water

Top load machine: the cycle can not start because it will not hold water in the tub. It just keeps draining out.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same problem here. But according to Maytag Service, the draining pipe may be too deep inside the draining tube on the wall, thus creating a siphon effect and not allowing the tub to fill.
Their suggestion is to ckeck the pipe and make sure no more than 6-8 inches are inside the draining pipe. This should take care of the suction. We'll see, Imma do that when I get home.

Posted on Jan 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to keep the water in my Roper top load washer overnight so it will soak the load of whites I have started but the machine drains.


You should be able to select a soak cycle without having to turn off the water supply, but it may time out eventually and drain the tub. This p[events oversoaking the clothes

Oct 13, 2012 | Roper RAS8445KQ Top Load Washer

1 Answer

I have a Kenmore 500 top load washer that doesn't hold water. As it is filling for the wash cycle all the water runs down the drain


The drain hose outlet must be higher than the 'full' water level in the tub or the water will syphon out until the tub water equals the hose height. If the drain system you are using for the washer is floor level, then you need to install a vertical pipe (1-1/2" minimum) to place the hose end into at the top and it should eject the water through a 90 degree elbow onto the floor at the bottom. There are more elegant solutions, but this will stop the tub from self-draining. Good luck!

Aug 05, 2010 | Kenmore 22422 Top Load Washer

1 Answer

Machine keeps overflowing during wash cycle


Your pressure switch stops the water and allows it to start the next cycle. It's a switch either in the control panel or at the top of the tub with a small tube connected to it which goes down between the inner and outer tub. As the water level increases the air in the tube is compressed until there is enough pressure to make the switch stopping the water from filling. This tube can get clogged and the switch won't work. Remove the tube and clean it out. Blowing on the tube when it's still connected to the switch will make the switch if it's working and clear.

Water inlet valve

If it fills with water and starts the cycle and the water keeps running in then your water inlet valve on the back where the water supply comes in is sticking. It needs replacing.

May 20, 2010 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Is some water in the tub of a top loading washer normal?


It is normal to have residual water in the drain lines and pump following a wash cycle. This is the low point of the drain cycle and gravity will ALWAYS cause some water to be there. As long as the water is not visible in the spin basket, you have nothing to worry about.

Some model washers also have a balance ring around the perimeter on top of the wash tub that is filled with fluid. This acts as a stabilizer to help keep the washer balanced during the spin cycle. If you have any questions, please post back and let me know. I hope this is helpful to you.

Apr 21, 2010 | Whirlpool WTW5200S Top Load Washer

1 Answer

The water will not drain. The tub starts


The pump is clogged. The only way to fix this is to clamp off the hose to the tub and remove the hose from the pump and remove what ever clogged the pump. Expect to get a little wet.

Mar 04, 2010 | GE WBSR3140DW Top Load Washer

1 Answer

I have the GE whdsr209doww- leaks all through cycle at the back draintube. I am going to get a new drain tube , but could it be the pump not holding the water in the tub?


FYI, the pump does not have a valve which prevents the water from leaving the tub during wash cycles.
If you were to remove the drain line from the machine the water in the tub would siphon.
I think you are moving in the right direction by replacing the drain tube. Also inspect the other connections from the tub to the water pump and water pump to drain tube..
Good luck...

Oct 12, 2009 | General Electric WHDSR209DWW Top Load...

1 Answer

FISHER PAYKEL WASHING MACHINE STUCK IN RINSE CYCLE


lift the end of the drain hose see if the tub fills and goes in the rinse cycle if it works you have a syphon problem if so make your drain pipe stand longer.

Aug 06, 2009 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Water keeps draining LG WF-561SPP top loader


If the cycle does not stop draining that is usually because of a faulty membrane switch that controls the water level in your appliance.
The faulty sensor cause the machine to think that there is still water inside, even when water has drained completely.

Apr 02, 2009 | LG WM3677HW 3.7 cu.ft. Front Load Washer...

1 Answer

Fisher & Paykel wahsing machine GWL10 stuck in rinse cycle.


no power from the control board to the diverter.replace control board.it is about $150.00 for the part

Jan 21, 2009 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Water runs into tub but does not fill?


be sure the drain hose is not lower than the wash tub this will caust the water to run out, 2nd be sure the drain hose is not pushed to far into the house stand pipe and the there is rome for air to go inbetween the drain hose and stand pipe eather of these will cause the machine to siphon mostly on rince cycle or on the 2nd and third loads you do. last your house drain could be starting to back up fill the washer with water and listen to it drain if you hear a gurggling sound in the house pipe you may need a plumber to cleanthis out for you.

Jan 19, 2009 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...