Question about Canon PIXMA MP830 All-In-One InkJet Printer

1 Answer

Why is my Canon Pixma 830 Printer beeping once upon start up, the screen lights for a second then the printer shuts off?

I have tried to reset unit by pressing the start button 10 times and then holding button in for 10 seconds then plugging printer back into the power source. I obtain the same results 1 quick beep and the screen illuminates for a very short time the printer immediately shuts down. This has been a great printer so far!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Canon Expert
  • 394 Answers

Either a power supply fault or there is a fault in the main circuit board. You may find a replacement power unit (they are held in by two clips ) at an electronics recycler or auction site like e-bay, but the main board is not an available part.

Posted on Dec 11, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 197 Answers

SOURCE: Canon iP4300 is noting "offline or no power" blinking orange light 3 times then turns off

maybe you have some driver issues..

go here, get new ones, re install

Posted on Jun 16, 2008

  • 1 Answer

SOURCE: THE PRINTER IS BLINKING ORANGE FIVE TIMES ORANGE AND THEN ONE TIME GREEN

I have the same problem blinking orange 5 times and 1 green, please help

Posted on Oct 04, 2008

huntwolfe
  • 20 Answers

SOURCE: Canon Pixma ip3000 flashing amber 6 times

If the 6 flashes are accompanied by an on screen message #5400, this is a "Service Call Error" code.

This code indicates the following;
Internal temperature error [5400]
The solution to this is the following part replacementl
- Logic board ***'y (QM2-1548) *1

*1: Before replacement of the logic board ***'y, check the waste ink amount (by service test print or EEPROM information print). If the waste ink amount is 7% or
more, also replace the bottom case unit (QM2-1205) or the ink absorbers (QC1-4222 / 4223 / 4224 / 4263 / 4264 / 4864 / 4221 / 4257) when replacing the
logic board ***'y.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]

Good luck!!!

Posted on Oct 02, 2009

  • 185 Answers

SOURCE: Printer won't read my refilled cartridge for my

many moidern printers are fitted with programs that are abkle to identify and refuse refillwd cartridges.
The sloutioni snot to allow it to go emty, before refilling.
Tro go to the web page of te manufacturer of the refiller, or probably thechain store that refilled the cartridge,.
They usually hav ethe speps to take to reset the cartridge error.
for the time being Try unplugging the printer, then power it on while it isunplugged.
then let it sit overnight. plug it in and see if it will reset.

Posted on Jan 20, 2010

pineworks
  • 4345 Answers

SOURCE: Current Problem on Printer """E5"""

This error means waste ink counter is full.

Solution:
1. Start with printer OFF
2. Hold down RESUME and then hold down POWER
3. Release RESUME
4. press RESUME twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Press resume

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon pixma mx416


Hi. Its not the power button permanently pressed?

Feb 10, 2018 | Canon PIXMA Office Equipment & Supplies

3 Answers

Canon Pixma MP530 multifunction printer


HI,

1.Power off the printer

2, Unplug the printer's power cord, wait 5 seconds then replug the power cord in.

3, Hold the Power button for 6 Beeps

4, Release the Power Button



Sep 15, 2008 | Canon PIXMA MP530 All-In-One InkJet...

1 Answer

Canon mp250, not printing. Print screen says "creating print data" and freezes there.


This sounds like an internal memory problem and I don't have a workaround. Before you give up, try this technique to reset the printer to factory. They are great printers once you learn this reset technique. Turn off printer. Hold down Stop/Reset button with one hand and turn printer on with other hand. After green light comes on for the ON button, press the Stop/Reset button two times and you should see the green light blink off and the orange alarm light blink "on" with the first press and then the green light comes back on for the power button and the orange light goes off with the second press (if you did it correctly). Now, you need to hold down the ON button about five seconds, then let go to shut OFF the printer. When you turn it back on, the printer should be back to the factory original condition. Make sure you set all your printer properties the way you want them again from your printer properties dialog boxes because some of the settings may have been stored in the printer's EEPROM, which you just reset to get rid of the offending alarm code.

Jan 20, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

2 Answers

I need to know how to reset my printer, I 've cleaned the pads, but nothing... Thank you in advance...


Power down the Canon Pixma IP4300. Once it has shut down, leave it off for a few moments.
Hold down both the "Resume" button and the "Power Button." When the printer begins to restart, release the "Resume" button but continue pressing "Power."
Push in the "Resume" button twice, then let go of both the buttons. In a moment, a green light flashes a few times.
Press the "Resume" button four times once the green flashing has finished.
Push the "Power" button again until the printer shuts down. Wait a few seconds, then press the power button again to restart the device. The Canon Pixma IP4300 will now function properly. for more information http://www.fixyourownprinter.com/forums/printer/67824 hope this helps you.

Aug 18, 2010 | Canon PIXMA iP4300 InkJet Photo Printer

1 Answer

Canon MP 830 I replace purge unit


You may need a new printhead now, or you may have left a foam packing block inside the new purge unit.

Oct 29, 2009 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

I have a error code 6A00 and alarm light flashing on my canon pixma mp 830


Canon lists the solutions for the error 6A00 as...

1.
Press ON/OFF switch to reset the multifunction device
2.
Press Stop/Reset and ON/OFF to reset the printer
3.
Removing paper jams
4.
The MP830 may require repair
5.
Unlock the scanner lock switch (MP830)

Oct 16, 2009 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

My canon mp 830 all-in-one printer says 6A00,


no need to reset your printer, the things your should do is you just open the over at the back of your printer, then you can see a paper hang on, then please remove it, then try to print, if it does not work open also the tray which is your bond paper stored, just see if there is also a bond paper hang, then remove it, then print again, that the cause of paper jam 


 Good Luck!!
 Nice

Jul 01, 2009 | Canon PIXMA MP830 All-In-One InkJet...

2 Answers

How to reset low ink warning in mp145


Following is the procedure to reset waste ink counter Canon Pixma MP145 :
  • Connected Printer to a Power source, Turn off the printer if printer on
  • With the Printer power off, press the Power button while press and hold Stop/Reset button.
  • When the Power led is light, press Stop/Reset button two times while pressing and holding the Power button.
  • When releasing the Power button and the Stop/Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
  • When the on/off lights in green, press the Stop/Reset button four times to reset wase ink counter. For other specified number pressed function listed in the table below. (Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange).
  • Unplug cable power from a power source.


The number of the Reset button pressing LED Function Remarks 0 time Green Power off 1 time Orange Service pattern print 2 times Green EEPROM print 3 times Orange EEPROM reset 4 times Green Waste ink counter reset

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Dec 20, 2008 | Canon PIXMA MP150 All-In-One InkJet...

2 Answers

MY PRINTER


strip the purge unit ( cleaning/waste unit ) out. its got stuck of all the waste ink inside the purge unit that got dry. the machine is thinking that there is blocking of paper or it cant get the printer head to its home posision. and also clean the carrige unit bar. normally this is done by a printer tech.

Nov 07, 2008 | Canon PIXMA iP4200 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA MP830 All-In-One InkJet Printer Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

old marine
old marine

Level 3 Expert

2256 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...