Question about Sharp AR-BC260 Color Copier
Posted by Anonymous on
Good day, my Sharp AR 5731 showing the message Call for Service . Code : H4-00 can you help me to fixed my problem. thanks and God Bless
Posted on Sep 24, 2014
F2-02 and f2-04 can you help me plz
Posted on Apr 01, 2014
Hi my sharp ar5731 is showing L4-31 Error Code plz can u help me .........THANKS
Posted on Jul 01, 2013
F2 04 did you just refill this device please change chip
H4 - press - # interpt C interept then 14 & start
Posted on Dec 03, 2017
My sharp 5731 did not display and the fusing unit is on.what can I do
Posted on Oct 19, 2017
My sharp 5731 photocopier is showing code error h2-01
Posted on Aug 21, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Dear sir; This error code means "scannor memory" problem, don't worry, we can reset it, the procedure as follow;
1, make sure you are in copy mode , then press "p", "*", "clear", "*".
2, enter 16 press start.
3, press "CA" to end simulation.
that's easy, if you need more help, just let me know, good luck.
HAVE A HAPPY HOLIDAY !!!
Posted on Dec 20, 2008
SOURCE: error code Sharp AR-M 257
The F2-04 error code you are getting is that you are using the wrong toner.It may be form sharp,but it toner chips is different.Only the chips swapping at the toner back can help you.
Posted on Jan 27, 2009
CH - open cover in the paper feed area
CH blinking - Dev unit is not properly installed
For the 'CH' check the covers and make sure all covers are closed properly.
For the 'Blinking CH' take the dev. Unit open and the reinstall unit properly.
Pls rate – thank you
Posted on Mar 03, 2009
H3-00 means there was a problem in the fuser unit of the copier - a temperature problem. The correct temperature is not reached within a certain time.
It could be a thermostat or thermistor problem - both monitor temperature. you could remove the fuser unit and make sure these items are clean - no build up on them. there should be a center and side thermistor.
You can reset the error code in SIM mode by pressing the following keys one after the other "P" "interupt" "C" "interupt" then 14 and start/copy key. confirm if required. make sure the copier is restarted afterwards.
If the error persists then you may need new thermistors.
Hope this helps.
Posted on Apr 12, 2009
the DK message means it is time to replace the black drum unit. the drum unit is called an ARC26DU. open the front cover. remove the toner cartridge/s by lifting the green
lever and pulling the toner out. Open the left side door. look at where
you just pulled out the toner and there is one screw (facing you)
holding each drum in place - loosen the screw and pull the drum unit out
towards you....slide in the new drum unit.
to reset drum counter go into SIM mode by pressing the following keys one after the other "P" "*" "C" "*" then 24 and start/copy key then 7 then select the color drum you are replacing and confirm reset. make sure copier restarts afterwards
DO NOT refill these toner cartridges (even if you can find someone to do it) The toner cartridges for these machines have generally had ongoing problems as far as longevity and quality - refilling them will only make it worse.
Posted on Apr 23, 2009
Tips for a great answer:
Mar 24, 2018 | Epson Office Equipment & Supplies
on Aug 03, 2010 | Office Equipment & Supplies
Feb 05, 2014 | Precor Exercise & Fitness
Dec 24, 2013 | Washing Machines
Aug 07, 2013 | Canon imageRUNNER 600 Printer
Aug 11, 2010 | Ricoh Aficio 450 Copier
Jul 25, 2010 | Canon iRC3100 Printer
Jul 06, 2010 | Canon imageRUNNER 2200
Jun 26, 2010 | Canon iRC3100 Printer
Feb 21, 2010 | Canon ImageRUNNER 3570 Copier/Printer
2,674 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: