Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

How can i get to the ballast ballare fmt on a mitsubishi wd62528 62 inch tv?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 213 Answers

YES IT BY THE LAMP

Posted on Nov 25, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
yambo
  • 230 Answers

SOURCE: Looking for a ballast part number and price Mitsubishi WD-C657

encompass.com or parstore.com is a good store parts.
Just provide model number tv.
Thank you

Posted on Aug 07, 2009

gopakumarg43
  • 76100 Answers

SOURCE: how can i get to the ballast board are fmt board on a mitsubishi wd62528 62 inch tv?

You're asking the way to access the ballast board, I assumes and posts this solution. You have to disassemble the set. If you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over 2250 posts now. All are related to electronic equipment repair help. Search the site by 'Timeslide' option. It will make search easy. Or, type in the brand name to your device into its search box, and press "Enter" Disassembley procedure is given in detail with illustrations. I can't include all that illustrations and descriptions here by this window.

Posted on Apr 11, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a Mitsubishi TV model# WD-60735.. we have changed the lamp because it was flashing red but now its flashing yellow and the tv will not turn on..


Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Nov 18, 2015 | Mitsubishi Televison & Video

1 Answer

How can i get to the ballast board are fmt board on a mitsubishi wd62528 62 inch tv?


You're asking the way to access the ballast board, I assumes and posts this solution. You have to disassemble the set. If you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over 2250 posts now. All are related to electronic equipment repair help. Search the site by 'Timeslide' option. It will make search easy. Or, type in the brand name to your device into its search box, and press "Enter" Disassembley procedure is given in detail with illustrations. I can't include all that illustrations and descriptions here by this window.

Apr 11, 2013 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Wd-60737 mitsubishi blinking yellow status light ?


Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Oct 25, 2012 | Mitsubishi WD-60737 TV

1 Answer

I have a mitsubishi wd-52631 and the red light is solid I just cleaned out the tv and got a new bulb but when I turn the tv on I get about 2 mins of picture and sound before it turns off. Does any one know...


It is possible either did not get all the dirty areas in front, and rear of set cleaned out or even that the ballast for the unit is this problem since it powers the lamp---lamp will come on and then turn off for a number of reasons.

The set does have a self diagnostic feature which usually is:

Mitsubishi TVtroubleshooting
Here's something that might also be useful. After you turn on the set, and getthe regular red blinky lights, hold down the Device and Menu buttons togetherfor about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filtercover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cablebetween FMT and Engine disconnected

May 02, 2012 | Mitsubishi WD-52631 52" Projection HDTV

1 Answer

I have a mitsubishi wd62725 green flashing led non stop replaced all the bad caps, 2 big and 4 smaller on power 4 1000u on fmt and 4 1000u on the dm board still getting the non stop led if i boot up with...


You can press the "DEVICE" and "MENU" keys on the front of the TV (not the remote) and the TV should flash an error code. Here is a chart.

Error Code Probable Cause
12 No error detected
22 Recovery from momentary Reset
32 Lamp Cover open
33 Air Filter Cover open
34 Lamp abnormality
35 Chassis Fan failure
36 Exhaust (Back Cover) or Lamp Ballast Fan failure
37 Engine (DMD or Lamp) Fan failure
38 Excess Lamp Temperature
39 Excess DMD Temperature
41 Short Detected
44 DVI Cable (between Chassis and Engine) disconnected

If the code is lets say 36 the LED will flash 3 times then pause then 6 flashes.

May 22, 2010 | Mitsubishi WD-62725 62" Rear Projection...

2 Answers

I replace the lamp into my mitsubishi 61 inch tv lamp number 915P28010 however the lamp took to the tv. Now when I hit the power button the tv will not come on but u can hear the fans runnin. I had someone...


Question?

is your TV making any strange sounds like clicks or any thing else?

YES? ....making noises is the "Ballast"


76e90fc.jpg

http://www.discount-merchant.com/MITSUBISHI-38169103GR-Lamp-Ballast-Driver-p/1137373.htm

if you see half of your tv black or out of shape is the light engine!



7a6cd45.jpg

http://www.discount-merchant.com/MITSUBISHI-RMD52-939P977A10-Light-Engine-p/1120406.htm



so i think it's going to be the ballast..



let me know i can help you more..




good luck!

Dec 31, 2009 | Televison & Video

3 Answers

Mitubishi WD 62725 - Ballast Problem??


the capacitors on the power board are the most likely the cause of the problem.

Jun 21, 2009 | Mitsubishi WD-62725 62" Rear Projection...

3 Answers

Mitsubishi tv


ok.
#1. replaced capacitors on power board. DM board FMT board .
# 2 on power board you need to chek caps. 3300mf x 35 v.QTY 2.
# 3 12 capacitor 1000mf x 16 v.
If caps 1000mf x 16 v . looked good. replaced anyway......

Sep 14, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Wd 62525 honeycomb pictues


The DM board wont cause that symptom. The DM only directs power that is recieved from the PWB to the ballast fans and etc. That sounds like a problem with the FMT. capacitors 1000uf @16volts numbers C8F21, C8F22, C8F19, and C8F27. those will cause distortions in the video on the V26 chassis. Let me know if you need more info

Mar 27, 2008 | Mitsubishi WD-52525 52" Rear Projection...

3 Answers

Mitsubishi WD-62526


Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.

For example, 3 flashes, then 7 flashes = 37.


Here are the error codes, and the corresponding problem:

12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Jan 13, 2008 | Mitsubishi WD-62525 62" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...