Question about Copystar Kyocera Taskalfa 181 Copier

Open Question

Connection error 0x2102 - Copystar Kyocera Taskalfa 181 Copier

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to retrieve Cisco router password without losing configuration?


You can't, otherwise there would be no point in having a password would there!

Dec 24, 2016 | Cisco Computers & Internet

2 Answers

Reset password Catalyst 4006 Ethernet Switch


Hi,

Depending on the Supervisor Module model, most likely it's a standard Cisco's "password recovery procedure":

Connect to the console
Reboot the switch (power cycle)
Start pressing Ctrl-C till you get to the BOOTROM
Change boot configuration register to 0x2142 (confreg 0x2142)
Boot the switch. It will ignore confuguration and boot "empty".
Go to "enable mode".
Copy startup configuration to running configuration ("copy start run")
Change boot register back to 0x2102 (conf t -> conf 0x2102)
Write config (write mem)
Reboot

Good luck,

Mike / CCNP, CCDP, CCSP, CCVP

Headset Adapters for office phone system

May 03, 2016 | Cisco Catalyst 4006 Chassis ( 4006)

1 Answer

What is the default password for cisco


There are two main methods to return a Cisco router to its original factory defaults. These two methods are described below.
Method 1
1. uses the config-register 0x2102 command in global configuration mode.
2. Check the configuration register on the router by issuing the show version command.
3. The configuration register setting is displayed in the last line of the show version command output and should be set to 0x2102. If this is not the case, enter the config-register 0x2102 command once in global configuration mode.
router#configure terminal
router(config)#config-register 0x2102
router(config)#end
router#
4. If the show version command is issued again, the same line in the command output will have '(will be 0x2102 at next reload)' appended to the current register setting.
5. Erase the current start-up configuration on the router with the write erase command.
Reload the router with the reload command. When prompted to save the configuration, DO NOT save.
router#reload
System configuration has been modified. Save? [yes/no]: n
Proceed with reload? [confirm]
Once the router reloads, the System Configuration Dialog appears.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]:
The router is now reset to the original factory defaults.
Method 2
1. uses the config-register 0x2142 command in global configuration mode.
2. Enter the config-register 0x2142 command in global configuration mode.
router(config)#config-register 0x2142
This causes the router to ignore the start-up configuration on the next reload. If a show version is issued, the last line in the command output will have '(will be 0x2142 at next reload)' appended to the current configuration register setting.
3. Reload the router using the reload command in enable mode. It is not necessary to save when prompted to save the system configuration.
router#reload
System configuration has been modified. Save? [yes/no]: n
Proceed with reload? [confirm]
After the router has reloaded, the System Configuration Dialog appears.
4. Enter no to the question "Would you like to enter initial configuration dialog?"
5. Change the configuration register setting to 0x2102 by entering the config-register 0x2102 command once in global configuration mode.
6. Issue the write memory command in enable mode to overwrite the existing start-up configuration with the current running configuration.
7. Reload the router with the reload command in enable mode.
Once the router reloads, the System configuration Dialog appears.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]:
The router is now reset to the original factory defaults.
Note: The configurations below are stored in ROMMON, and cannot be reset to Factory Default Settings by the write erase or config-register 0x2142 commands.
warm-reboot
memory-size iomem <not default>

Jun 18, 2013 | Computers & Internet

2 Answers

I have forgotten my passwork to my wireless cisco linksys E3000, how do I go about retrieving it?


he WEP key is defined by the person who set your wireless router up. You will not be able to find out what the WEP key is, but you CAN change it if you have physical access to the router. If you are trying to connect to your wireless router and can't remember the WEP, then walk over to the router and on the back or bottom of it is a small little hole that you can fit a pen or paper clip into. Press the paper clip into the little hole for 10 seconds and release. This will reset all the settings on your router back to default and will allow you to access your wireless connection.

Note: doing this will take away all of your wireless security so make sure that you know what you're doing before messing with it!

Thanks and please rate if this helps you at all :).

Mar 29, 2011 | Cisco Linksys Refurbished E3000...

1 Answer

Cisco 2514 does not switch on straight away. It powers on about 1min after switch depressed. it also loses the correct date and time if switched off.


if you issue the command show version
At the bottom written in bold you should the config register settings these nee to be as shown at the bottom of this page


R1#show version
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-JS-L), Version 12.1(3), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Thu 06-Jul-00 10:02 by cmong
Image text-base: 0x0306F914, data-base: 0x00001000

ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE SOFT
WARE (fc1)

R1 uptime is 1 day, 5 hours, 39 minutes
System returned to ROM by power-on
System image file is "flash:c2500-js-l.121-3"

cisco 2500 (68030) processor (revision N) with 14336K/2048K bytes of memory.
Processor board ID 11844920, with hardware revision 00000001
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)

Configuration register is 0x2102

if yours differs the use the these commands to correct it


R1>en
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#config 0x2102
R1(config)#^Z
R1#


Hope this helps

Mar 15, 2011 | Cisco 2514 Refurbished Router (CSCO2514)

1 Answer

Password Recovery for Cisco Catalyst 4506


Please see Cisco's page at http://www.cisco.com/en/US/products/hw/routers/ps5199/products_password_recovery09186a0080093e12.shtml
for step by step details and more in depth instruction.

1. Reboot
2. Press the "break" button on your keyboard within 60 seconds of the power-up to put the router into ROMMON mode.
3. confreg 0x2142
4. reset
5. type, "no" when prompted to enter the initial configuration dialog.
6. enable
7. copy startup-config running-config
8. conf t
9. enable secret <password>
11. config-register 0x2102
12. reboot again

Jan 20, 2010 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

I m in rommon booting problem.my router version 1750.how can i exit from rommon?help me.


you need to change the config register back to 0x2102.
type "?" and find the command to change startup settings, go through the list (I'm working from memory here, sorry) and make sure it is NOT ignoring startup settings. There may be a way to edit the config register value directly, can't recall.

Aug 11, 2009 | Cisco 1750-4V Router

1 Answer

Bootup Router and then nothing


Hi,
Your router is in the wrong mode. You need to change this by changing the conf-register to 0x2102

at the rommon prompt type in

config-reg 0x2102

reboot

If there are any errors you can get the correct syntax by typing ? at the rommon prompt the line number will go up on every line.

The way to get into rommon mode is by pressing the break key from Hyperterminal as the router is rebooting. So make sure you don't do this by accident. If you do just reboot by power cycling.

Your Startup Config should be unchanged, but you need to be very careful what you do in rommon mode it is easy to blat stuff.

Any changes you make once you get into the command (enable) mode should be saved by
copy running-config startup-config

Any problems just let me know.

good feed back would be much appreciated.

Carrie

Dec 05, 2008 | Computers & Internet

1 Answer

Cisco 857 router


You might need to reset the password. In order to do this, follow these directions:

  1. Console into the router, then power cycle it. As its rebooting hit the "break | pause" button on your keyboard, and you get to the rommon1> prompt.
  2. Then type rommon1>confreg 2142 rommon2>reset
  3. The router comes back on as if it were new---answer no to the first question, and sometimes it asks a second question (do you want to terminate autoinstall, or something...)---answer yes to the secondquestion if it asks. Then hit enter and you get router> in a few seconds.
  4. Then router>en router#copy start run

create a new account:
  1. router#conf t
  2. router(config)#username bob priv 15 password bob
set register back:
  1. router(config)#confreg 0x2102
  2. router(config)#exit
  3. router#wr
  4. router#reboot

and that should let you login with bob/bob

Nov 30, 2008 | Computers & Internet

Not finding what you are looking for?
Copystar Kyocera Taskalfa 181 Copier Logo

Related Topics:

801 people viewed this question

Ask a Question

Usually answered in minutes!

Top Copystar Office Equipment & Supplies Experts

Tammie Duggan
Tammie Duggan

Level 2 Expert

57 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

polytek

Level 3 Expert

453 Answers

Are you a Copystar Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...