Question about Rust-Oleum Prep Wipe

Open Question

How do i remove rust oleum leak seal - Rust-Oleum Prep Wipe

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can I apply Rust-Oleum Painter's Touch over Grumbacher resin based Final Varnish

The best solution you'll get from books at

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Jun 20, 2018 | Cars & Trucks

1 Answer

I just want to know if rust-olem paint on the inside of a microwave is bad for our health?

Please do call the Rust-Oleum company and ask them.
You should find their phone number on a can of their paint.
I would be highly suspicious that you should not be breathing those fumes, but they might be OK.
God bless your efforts.

Feb 21, 2017 | Microwave Ovens

1 Answer

Spray can won't spray its a full can

either defective sprayer or no propellant either return or try different spray tip

Sep 27, 2016 | Rustoleum Rust-Oleum - 1685830 - Spray...

1 Answer

How do you remove roll a tex from wall?

If latex based paint was used, most of the time it is, spray the area with warm water then use a flat scraper to remove.. It is very messy when doing a large area. Cover as many surfaces as you can to protect. Try a small area in a corner first to see how it will work, if it works fine then do the whole wall.

May 12, 2014 | Rustoleum Rust Oleum 22233 Roll-A-Tex...

1 Answer

Dry time for second coat spray paint without crinkle

read the really is that simple.
Good luck

Nov 11, 2013 | Rust-Oleum Corp Rust-Oleum Painters Touch...

1 Answer

The sun is so harsh on wood windowsills they crack in a couple of years and have to be repainted. Someone told me to use aluminum oil based paint on them prior to painting them. All I found is 402...

Usually when you have cracking on your windows, there's several variables including sunlight. One of the biggest problems is using the incorrect primer or a cheap paint. Contrary to what many believe, a primer that dries extremely hard is not ideal for exterior surfaces. Wood expands and contracts with heat, cold and moisture. A high quality latex primer, topped with a high quality exterior latex paint will give you the best results. It allows for flexibility but offers great protection. Some prefer an oil/alkyd based primer. This is fine as long as it's a slow drying primer. The quick drying primers have hardeners in them that don't flex well. Be sure to remove any loose and flaking paint before you prime them. There are places where you can cut corners with painting. I wouldn't do it on exterior paint. One last thing to be aware of- be sure it's not lead paint you're working with. That changes everything.

Oct 20, 2013 | Rustoleum Rust-Oleum 1030-402 402 Green...

1 Answer

Rusty pan on the trans of 94 1500. Want a stamped steel deep pan(tow a boat) trans if fine just not waiting for the pan to leak all over the driveway or worse.. Ideas?

A new pan can be found on ebay for about $75. I would check your local dealership first though. Either way, a few good coats of Rust-Oleum to slow up the rusting problem might be a good idea.

Jan 28, 2011 | 1997 Dodge Ram 1500 Club Cab

1 Answer

I have a gsx750f, a 2000 model, it seems to be getting some rust around the fuel filler section when you open the cap lid, how can I remove it (about 6 bolts I can undo) what else do i remove to safely...

I would get some naval jelly and brush it on and let it set as directed.
repeat if required, there are rust arresting products abailable that encapsulate the rust. or rust oleum if nothing else.

Dec 27, 2010 | 2000 Suzuki GSX 750 F (Katana)

1 Answer

Can I remove rust from drum with a scrubbie for temporary fix?

I'd use the brush to clean the spots down to bare metal then use something like Rust-Oleum appliance touch up paint (multiple coats) to cover the problem areas.

The Rust-Oleum costs about $4.00 .

In order to get access to the tub, see the following:

In order to get the agitators out, you need to remove the "Spanner Nut" and "Drive Block".

Many instructions call for a special spanner wrench to remove the nut. However,

You don't need a special spanner wrench. (About $20 retail)

I've used a short 10" pipe wrench (About $9 also good for cracking walnuts) hooked around one of the tabs on the spanner nut and tapped the handle with a hammer to loosen it.

Also, don't directly hit the drive block with a hammer (it's soft metal). Put a short piece of wood under the drive block and tap it up with a hammer.

You can then lift the drum out and more easily work on it.

Apr 10, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

02 malibu has a rusted screw on top of the engine block and some antifreeze is leaking out. Is there a sealant of some type that can seal the leak?

There's a number of different sealants that might do the trick. Unfortunately, it will be near impossible to get a good seal to the rusted/dirty surface. Can you remove the bolt? If so, it would be much better to remove it, clean the threading inside the block and install a new bolt (using sealant on the threads).

Jan 19, 2009 | Chevrolet Malibu Cars & Trucks

Not finding what you are looking for?
Rust-Oleum Prep Wipe Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rustoleum Vehicle Parts & Accessories Experts


Level 3 Expert

85206 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14750 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Rustoleum Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides