Question about LG 50PX5D 50 in. Plasma HDTV

Open Question

Lg plasma 60pn5500

Picture setting and calibrations

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The calibration settings for an LG 65UH8500 under picture mode Isf Eepert (Bright Room). Thank You.


http://www.lg.com/us/support/product-help#

This is LG's support website so you can get the most specific/accurate specs & settings for your LG set

Apr 25, 2017 | LG Televison & Video

1 Answer

Do I need to calibrate this model? Any other suggestions?


I have seen services offered by some box stores to "calibrate" the color on televisions. (It was not a cheap procedure.) Is there a problem with a the picture? Did you reset the tv to factory settings and you still do not like the picture quality?

Jan 05, 2016 | Philips 42PF9630A 42 in. Plasma Television

1 Answer

How do I calibrate my lg plasma 60pn6500 tv


There are several HDTV Calibration discs available on amazon or other locations. They will walk you through calibrating all the available levels on your television. Or you can contact any number of companies that will come out and calibrate for you, however they can be quite expensive. It really depends on how hands on you want to be.

Jan 06, 2015 | LG 60PN6500 60" Plasma TV 1920x1080, HDTV

1 Answer

How do I calibrate my Panasonic TC-P55ST50 for the best picture quality?


Tweak the factory default settings until you are satisfied with the results.

Oct 15, 2014 | Panasonic VIERA TC-P55ST50 55 in. 3D...

1 Answer

LG Plasma inch has black pixalation around moving pictures only.


It is likely NOT the set and if using a box for hd it could be it.

Most likely is signal is slow and set cannot keep up with it.

Mar 17, 2012 | LG Televison & Video

1 Answer

I have a sony kdf-46e2000, there is a pinkish stripe on the top and bottom of the screen, what is causing that?


Looks to me as an serious (but not uncommon) PSP board problem with Sony plasmas. Contact a Sony service center.

What problems have people had with quality control on these displays? Are they covered under warranty?
  1. Certain displays emitted an extremely loud buzz. This was covered by warranty repair.
  2. Certain displays had a problem with the Y/C delay on their S-video input. This was also correctable.
  3. One person reported red vertical lines on his display. Was this covered by warranty? Was it an input problem or a pixel problem?
  4. Afew bad pixels here and there are not covered under warranty. Largeclusters are generally covered. It's up to Sonys discretion. On the plus side, however, bad pixels are becoming increasingly rare. Mostpeople are reporting no bad pixels at all!
CALIBRATINGWhat needs to be calibrated on a plasma?
You needto calibrate most of the same things that need to be calibrated onother displays. About the only things that don't need to be done areconvergence and geometry. You can usually tinker with picture size andposition, but there's no need to deal with keystone or pincushionadjustments, etc.What is white level? What is black level? How are they adjusted?
Theadjustment for white level is usually labeled "Picture" (as onPanasonics) or "Contrast". "Brightness", on the other hand, refers tothe black level. Yes, this is apallingly counter intuitive. This FAQuses the terms "white level" and "black level", since they betterdescribe what you're actually adjusting, and they're the terms used byAvia and Video Essentials.
How do I adjust hue and saturation?
In another mysterious choice of terms, hue is controlled by the "Tint" setting,and saturation is controlled by the "Color" setting. This FAQ uses theterms "hue" and "saturation", since they're the terms used by Avia andVideo Essentials.
How do I set the white level on a plasma?
Youset the white level by adjusting the "Picture" setting. You will needto use a different test pattern than you would for a CRT. For both plasma displays and LCD displays, you should use the 10 IRE grayscalestep pattern. There are two criteria you want to match on your plasma.
First,you need to make sure the white level is low enough that your displayisn't thresholding (or clamping) bright levels. You should set thewhite level low enough that you can see each of the 10 IRE stepsdistinctly. The Sony seem not to exhibit clamping (in my limitedexperience), even at factory defaults, so this criterion may not beterribly useful.
Second, for the health of your display (e.g.to avoid burn-in), you should turn down the white level. Just becauseyour display can display blindingly bright pictures doesn't mean that it should. Plasma displays should be set between 21 fl and 25 fl light output; the Sony comeout of the factory at about 30 fl. On one ISF-calibrated Sony, 23fl was roughly equivalent to a Picture setting of -20 (in the usermenu, not the service menu). To set this precisely you'll need to bringin a calibration specialist, but you can do a lot of good by justdialing down the white level a lot. After seeing the display at 30 fl,23 fl will see very dim. But after a while, you'll find that 23 fl isplenty bright.
How do I set the black level on a plasma?
Youset the black level by adjusting the "Brightness" setting. You can usethe same test pattern you would use for any other display.
How do I calibrate grayscale (calibrate the color temperature)?
Unfortunately,this is one you can't do yourself. You need special equipment tomeasure the color. In fact, most ISF technicians lack the equipmentspecific to plasma calibration (a $15K gadget known as aspectroradiometer). But even the standard color measurement equipment(which calibrationists do have) will do a great job.
Thatsaid, one person who had his Sony display calibrated by an ISF specialist said that the Cinema / Warm setting was reasonably close to6500K out of the box. Using that setting is probably the best you'll doon your own.
If you're really determined to screw up yourdisplay, the RGB drive and cutoff settings in the service menu are used to adjust the color temperature.
How do I adjust the color decoder?
There are several issues here. Generally speaking, the Panasonic decoder seems topush blue a bit. The R-Y Axis Angle and B-Y Axis Gain in the servicemenu are used to correct this behavior.
There used to be aproblem on some Panasonics with the Y/C delay on the S-video input. Seethe Quality Control section for more information.
How do I adjust the gamma?
On the industrial model, there is a set of Advanced picture settings. Go to the Picture menu, turn Advanced on, and then hit the down-arrow. In the subsequentmenu you can adjust quite a few parameters, including select from a fewgamma settings.
This advanced menu appears to be missing from the consumer model.
How do I calibrate my consumer model given these missing menus?
Thereis apparently a way to activate these menus. Perhaps you can find acalibrationist or Panasonic technician would can turn them on longenough to do the calibration.
What's the overall calibration procedure?
In general, the order Avia sets out is the correct one. A more complete list is:
  1. White level (picture)
  2. Black level (brightness)
  3. Repeat (1) and (2) until you have a good balance.
  4. Grayscale (requires special hardware and mucking about in the service menu)
  5. Sharpness
  6. Hue and Saturation (tint and color)
  7. Color decoder (requires use of the service menu)
  8. Repeat (6) and (7) for red and green until you have a good balance.
SERVICE MENUHow do I access the service menu?
In a word, don't. See the service menu warningabove. If you're bound and determined to make use of the service menu,buy the service manual. It contains more than enough information foryou to ruin your display and/or kill yourself.

Aug 18, 2009 | Sony Grand WEGA KDF-42WE655 42" Rear...

2 Answers

LG Plasma has sound but no picture


Hi James,
This could be one of two problems. I can't narrow it down any further without having the set in front of me.
1. The plasma panel or the componets which supply electricity to the plasma in the panel have packed up.
2. The video processing unit in the set has gone.
As for the cost of repair, if it's the panel, buy a new TV. It'll be cheaper. If it's the component that supplies the electricity to the plasma on the panel or the video processing unit, expect to pay between 300-400 as a conservative estimate for parts. Labour would be another 100-200.

Hope this helps


Apr 28, 2009 | LG 42PX5D 42 in. Plasma HDTV

1 Answer

LG plasma tv made loud popping noise


The plasma gas tubes may be damaged or the gas couldve leak out. remember plasma have to remain upright at all times even when transporting them, if they are not you should just set it up straight for about 3-4 hours before turning it on.

Apr 23, 2009 | LG 50PX5D 50 in. Plasma HDTV

2 Answers

42" sony plasma wont power on


I don't think Sony makes a Wega Plasma. Sony did make a plasma about 7 years ago but it wasn't Wega. Are you sure it's not Grand Wega SXRD or Lcd type

Apr 13, 2009 | Sony Grand WEGA KF50WE610 50" Rear...

1 Answer

Lost half of picture


This can be on the matrix drive board, or the display assembly itself. It is possible to also have a defect in the address decoding area that will cause this.

The procedure is to swap out the suspect boards to determine where the fault is, leave the working boards in the set, and then follow up any necessary calibrations that are necessary.

Jerry G.



May 24, 2008 | LG DU-42PX12XC 42 in. Plasma HDTV

Not finding what you are looking for?
LG 50PX5D 50 in. Plasma HDTV Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Televison & Video Experts

Ekse

Level 3 Expert

13434 Answers

The Knight
The Knight

Level 3 Expert

76115 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you a LG Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...