Question about Computers & Internet

1 Answer

1999 tacoma sometimes the clock works sometimes not

I bought the truck used.at first the clock would not light up at all.after about 3 weeks it started to work just as I was getting ready to pull it out and send it in for repair.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 7,627 Answers

Wrong category.

Posted on Dec 13, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No tailights on my 2004 toyota tacoma


First check bulbs,Then check to see if your truck has a trailer hitch wiring connector,Sometimes they use a "t" connector to split the wires.Check for broken or corroded wires around the connector.

Jan 29, 2014 | 2004 Toyota Tacoma

2 Answers

1999 Toyota Tacoma tail lights work and then go off.


hello, it sounds like it could be the tail light relay, it's in the fuse box under the hood and marked on the cover diagram, ty a new one.

Jan 30, 2018 | 1999 Toyota Tacoma PreRunner

1 Answer

2006 toyota tacoma air cond fan only works sometimes


see a mechanic. electrical is the worst to do on your own.

Sep 15, 2012 | 1999 Toyota Tacoma PreRunner

1 Answer

My 1999 tacoma i bought has a cold air intake and its throwing a check engine light but it drives fine??? Help


drive it on over to oriellys auto parts and ask them to use thier scan tool (most parts stores can do this for you) itll tell you what part is causing the code to be thrown. however 9 times out of 10 when you have a check engine light on and the car still drives fine its the O2 sensor. on a side note most cold air intakes are a gimmick. most vehicles come stock with cold air intake from the factory. the issue ive noticed most with cold air intakes that use oil is they get over oilled and this cloggs up the IAC valve, TPS sensor, and throttle body.

Mar 13, 2012 | 1999 Toyota Tacoma PreRunner

1 Answer

6 months ago, replaced head gaskets. 1 week later, service engine soon light came on. Tech said it was an oxygen sensor. Cleared code. 3 weeks ago, got oil change, replaced headlights and replaced...


CHECK TURN SIGNAL FUSE.IT COULD BE BLOWED OR YOU HAVE FAULTY TURN SIGNAL SWITCH.BECAUSE BACK LIGHTS AND TAIL LIGHTS SHARE SAME CIRCUIT WITH TURN SIGNAL SWITCH.

Jun 26, 2011 | 1999 Chevrolet Venture

2 Answers

My heater does not work on my toyota tacoma 2007 prerunner, the fan is only working...


heater core might be blown-off. also see your fuses for heater under your dash fuse panel or at the under hood sometimes where they are.check your cold lever position might be at full cold counter clock wise, move it to hot position clock wise.

Jan 12, 2011 | 2007 Toyota Tacoma

2 Answers

The radio and the clock from tacoma 2002 did not


On most vehicle the fuse for the clock will be the same as the interior dome light. As for the radio should be a 10 amp fuse (red). Usually found on the interior fuse panel for both.

Nov 06, 2009 | 2002 Toyota Tacoma

3 Answers

1999 Honda accord dashboard clock light


use a eyeglass flat screww driver to pry the clock assembly up and out , disconnect the clock assembly and remove the bulb by twisting the the blue or sometimes grey round plastic bulb bottom to remove it from the assembly. install new bulb , twist clockwise to lock in place , reinstall assembly

Mar 21, 2009 | 1998 Honda Accord

4 Answers

Need to remove ignition switch


remove shroud
insert key into ignition turn to acc you will see a hole at the underneath of ignition housing with key on push in pin and pull switch out

Jul 24, 2008 | 1996 Toyota Tacoma

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Alun Cox

Level 3 Expert

2679 Answers

Brad Brown

Level 3 Expert

18067 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...