Question about Mitsubishi WD-52525 52" Rear Projection HDTV

Open Question

Wd-62627 code 44 DVI disconnected? I am able to get to one end and i disconnected and reconnected. Still the same. Solid red status light and 4 short blinks pause 4 short blinks. Any ideas?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: Mitsubishi WD-52525 Status Light --- blinking red constantly.

possible that over night your set took a power surge ,possible power supply fault.

Posted on Sep 12, 2007

Ad
tvguy171
  • 106 Answers

SOURCE: STATUS LIGHT SOLID RED ON 73 DLP MITSU MODEL WD73735

The colorwheel is your problem. To confirm this, unplug the tv, then listen thru the air vents in the back as you plug the tv in. You will probably hear a ticking sound. If you do, that is the colrwheel. If the colrwheel is working, youwill be able to hear it "spin up". It will be a sudden high pitch whine. Let me know if I can be of further assistance

Posted on Dec 19, 2008

  • 16 Answers

SOURCE: WD-52525 - No picture, green status light then turns to red lamp

check the lamp

Posted on Jun 26, 2009

  • 64 Answers

SOURCE: mitsubishi 62" dlp wd-62525

The lamp is either defective, not connected properly to the wiring or plugs (careful alignment required on the two connections), wrong type bulb, or the front panel is not replaced properly to trigger the panel sense switch (lower right side of panel)

Posted on Aug 01, 2009

  • 1 Answer

SOURCE: Red blinking status light on DLP Mitsubishi TV

how do you get the tv back on when the light keeps flashing

Posted on Sep 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 73" mitsubishi dlp WD-73827 turns off and has a red status light blinking. I have replaced the bulb and the heat sensor... any answer to what else could be the problem?


It is helpful to have the sequence of the blinking red light. This may help:

MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927

Page 43

3. Error Code Operational Check

Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational

Check. When the TV is switched Off, the code automatically resets to "12" No Error.



Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,

activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem

has occured since the last Initalization.



Note: The front panel buttons must be used, NOT those on the Remote Control.



• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.



Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.



4. Error Codes

The Error Code designations indicating malfunction, or no malfunction, are listed below:

POWER

LED

STATUS

LED

LAMP

LED

Power

Status Condition

Off Yellow Off Low

Power Excess heat. Check Lamp Filter

Off or On Off Yellow No

change

120w usage time over 7000 Hrs.

150W usage time over 3500 Hrs.

Off Off Blinks

Yellow

Low

Power Lamp Cover open

Off Blinks

Yellow Off " Filter Cover Open

Off Off Red Stby Lamp did not turn On

Off Blinks

Red Off Low

Power Fan Stopped

Off Red Off " Circuit failure (short or DVI

connector unplugged)

Abnormal LED Indications

Error Codes "DEVICE" & "MENU"



Error Codes Description



12 No error detected

22 Recovery from Reset

32 Lamp cover is Open

34 Lamp abnormality

35 DM Fan failed (Chassis Fan)

36 Exhaust or Lamp Ballast Fan failed

37 DMD Engine Fan failed

38 Lamp temperature abnormally high. Remove Lamp to check filter.

39 DMD temperature abnormally high

41 Short is detected (Standby Power Supplies)

42 Lamp Fan failed

44 DVI cable between Format and Engine disconnected

46 DMD Temp. Sensor not detected (check DT connector))

47 DM Temperature too high

48 Engine power supply short detected

51 Speaker Drive circuit short detected

52 HDD excess temperature (V30+ & V31 only)

55 HDD Fan Stopped (V30+ & V31 onlyt)

Jul 18, 2014 | Mitsubishi WD Televison & Video

2 Answers

What is error code 42 on wd62627


Double check as no 42 is indicated on their site.

Nov 29, 2012 | Mitsubishi WD-52627, WD-52628, WD-62627,...

1 Answer

Wd-60737 mitsubishi blinking yellow status light ?


Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Oct 25, 2012 | Mitsubishi WD-60737 TV

1 Answer

Mitsubishi dlp tv model wd-62627 wont power on when i plug tv in green light flas then will stop then i try to power on tv after after green light stops flashiing after oabout 30 sec red lamp light co


Inspect the lamp first to see if shattered--set has a self check feature also:

Mitsubishi TVtroubleshooting
Here's something that might also be useful. After you turn on the set, and getthe regular red blinky lights, hold down the Device and Menu buttons togetherfor about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filtercover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cablebetween FMT and Engine disconnected

May 30, 2012 | Mitsubishi WD Televison & Video

1 Answer

Same as jasonvonk mar 15 2010 I get error code 37 after device and menu buttons pushed. red lite blinks 4 short pause and 4 short again Jim


37 is lamp or dmd failure. i don't find anything on 4 red blinks.44 error code which is 4 blinks, and then 4 blinks in disconnected DVI cable from light engine.

Mar 25, 2010 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

Red flashing status light


Press and hold the "Device" and "Menu" for 5 seconds and see what code comes up....... 12 No error detected
22 Recovery from momentary Reset
32 Lamp Cover open
33 Air Filter Cover open
34 Lamp abnormality
35 Chassis Fan failure
36 Exhaust (Back Cover) or Lamp Ballast Fan failure
37 Engine (DMD or Lamp) Fan failure
38 Excess Lamp Temperature
39 Excess DMD Temperature
41 Short Detected
44 DVI Cable (between Chassis and Engine) disconnected

Apr 03, 2009 | Mitsubishi WD-62525 62" Rear Projection...

2 Answers

STATUS LIGHT SOLID RED ON 73 DLP MITSU MODEL WD73735


The colorwheel is your problem. To confirm this, unplug the tv, then listen thru the air vents in the back as you plug the tv in. You will probably hear a ticking sound. If you do, that is the colrwheel. If the colrwheel is working, youwill be able to hear it "spin up". It will be a sudden high pitch whine. Let me know if I can be of further assistance

Dec 19, 2008 | Mitsubishi WD-52525 52" Rear Projection...

2 Answers

Mitsubishi WD-62525 Red Status Light After Cap Replacement


A steady red light: there is a short on the DVI cable from FMT to DMD disconnected

Sep 09, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Mitsubishi WD52725 DLP


Your DVI Cable may be defective as a 44 code is DVI cable

Jun 21, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Hi troylove


the dvi cable could be bad in the set or needs to be sited. or one of the boards the dvi connects to. ( would bet it will be the DM board in the Chassis) it will need to be sent off for repair if it is the chassis.

Jun 21, 2008 | Mitsubishi WD-52525 52" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...