Question about Brother DCP-8060 All-In-One Laser Printer

1 Answer

How to reset toner life end message on dcp8060

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 9 Answers

The counter reset method depends on the cause of the toner life end message and the condition of the newly installed cartridge.
When a USED toner is installed the reset gear is set to IN USE.
When a NEW toner is installed the reset gear is set to FACTORY SET.

Posted on Dec 28, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ctf1800
  • 4402 Answers

SOURCE: brother dcp 7020 says toner end life

unplug plug it back in, did you remove the protective cover and clean coria wire?
http://welcome.solutions.brother.com/BSC/public/us/us/en/faq/faq/000000/000000/000065/faq000065_018.html?reg=us&c=us&lang=en&prod=dcp7020_us

Posted on Dec 20, 2007

bowdo
  • 78 Answers

SOURCE: toner low, tone life end

There is a gear on the left hand side of the toner to reset the toner count this can cheated be rewinding it. Yes the design is to stop the refillers or at least slow them down a bit. If this fails purchase a new genuine toner but I have seen problems with the switch that resets the toner (Either the spring on the switch has popped off or the main board has failed).

Posted on Jan 21, 2008

  • 4 Answers

SOURCE: how to get ride of Toner life end message

You could try resetting the toner cartridge settings. OPen the machines front door where you would replace the cartridges. On the top panel you will see a "clear/back" button. Press it and on the display you will see a reset menu come up. Arrow to each one and hit the OK button. Press "1" to reset. Once you have gone through all close the front door of the machine and press stop to bring the display back to normal.

Hope this helps.

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset life toner end message


Easiest way to find out how: go to youtube, search for reset and your printermodel. I found my reset method there.. Good luck.

May 16, 2014 | Brother DCP-7040 Laser Printer

1 Answer

Toner life end message despite new toner


. To reset the "Toner Life End" message on the Brother MFC-8460N Open door press Clear/Back key

Apr 22, 2014 | Brother MFC-8460N All-In-One Printer

1 Answer

Brother MFC-9440CN Laser Printer is saying toner life end and I just put a new cartridge in.


If you want to reset your Brother MFC 9440N machine so you no longer have the error message: Toner End of Life, do the following:

1. Open the front cover of the 7820N, that is, the cover that allows you to pull out the toner and drum, but don't pull out the drum/toner.
2. Push the button: Options (located on the left of the control pad).
3. Type: *00 on the keypad.

The Brother MFC 9440N should be reset and the Toner End of Life message should disappear. Warning, this may void your warranty and ultimately damage your machine if you are reusing or refilling your cartridges, but you should already know that. Hope this helps.

Nov 11, 2010 | Brother MFC-9440CN Laser Printer

1 Answer

Brother MFC 7820N Toner life end with new toner


I found the following post on another site. It appears to work. If you want to reset your Brother MFC 7820N machine so you no longer have the error message: Toner End of Life, do the following:

1. Open the front cover of the 7820N, that is, the cover that allows you to pull out the toner and drum, but don't pull out the drum/toner.
2. Push the button: Options (located on the left of the control pad).
3. Type: *00 on the keypad.

The Brother MFC 7820N should be reset and the Toner End of Life message should disappear. WARNING: This may void your warranty and ultimately damage your machine if you are reusing or refilling your cartridges, but you should already know that. Hope this helps.

Sep 07, 2010 | Brother MFC-7820N Printer

2 Answers

Toner Life End message on DCP-7040


If your cartridge has a lever on the left side near the rear, it needs to be reset, and there's a lever inside on the left that can stick and cause that error. You need to wiggle and pull that lever until it moves freely again.

Jan 04, 2010 | Brother DCP-7040 Laser Printer

1 Answer

How to get ride of Toner life end message


You could try resetting the toner cartridge settings. OPen the machines front door where you would replace the cartridges. On the top panel you will see a "clear/back" button. Press it and on the display you will see a reset menu come up. Arrow to each one and hit the OK button. Press "1" to reset. Once you have gone through all close the front door of the machine and press stop to bring the display back to normal.

Hope this helps.

Oct 17, 2009 | Brother MFC-9840CDW Laser Printer

4 Answers

Dcp 7020 and 7040 toner life end message premature, need override


When the Toner Life End LED flips on, requires you to replace the cartridge, even when there's still toner left in the cartridge. The machine detects end of life by shining a light through from one side to the other.
To circumvent the detection mechanism, remove the cartridge and put a piece of masking tape over or jam a little bit of paper into the clear opening/circle on the right side of the toner cartridge, and then pop the cartridge back in. Eventually, you'll start seeing streaks, and then you'll know that the cartridge is truly empty.

Jan 17, 2009 | Brother DCP-7020 All-In-One Laser Printer

2 Answers

Toner life end message flashes


did you reset the toner life?

open the front cover, press the option button, on the screen will display ''reset toner life 1 yes 2 no ''
press 1 and close the cover.

toner life reseted

May 06, 2008 | Brother MFC-7820N Laser Printer

2 Answers

MFC 8460N giving Toner Life End message


I just solved my own problem. Try it for yours. I had been using several compatible toners for the MFC-8460N with no problems until today, as I posted earlier. On a hunch, I went to the local office supply store and purchased one original Brothers TN550 toner and put it into the printer and closed the cover. Everything clicked. Toner End Life message gone. I then took that Brother toner out and put the compatible one back in and still everything was fine. Am keeping the original Brother toner as a "kickstarter" if it happens again.

Mar 10, 2008 | Brother MFC-8460N Laser Printer

2 Answers

Toner life


where and how to find the reset actuator?

Nov 06, 2007 | Brother IntelliFax-2820 Laser Fax

Not finding what you are looking for?
Brother DCP-8060 All-In-One Laser Printer Logo

393 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

James Cagle
James Cagle

Level 2 Expert

481 Answers

Jim Keysor

Level 2 Expert

331 Answers

ctnozil

Level 2 Expert

270 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...