Question about KitchenAid Artisan Series Tilt-Head Stand Mixer

Open Question

Kitchen adi only runs on one speed

My kitchen aid only runs at one speed high

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 25 Answers

SOURCE: Kitchen aid KSM90

If you can unplug the mixer and test resistance between leads of the selector switch. The resistance should vary from high to low as you move the selector from low to high. If cord and all else looks good and switch is bad replace the switch.

Posted on Mar 26, 2008

Ad

seakish

  • 492 Answers

SOURCE: Kitchen Aid 10 speed 325watts

Some of the gears may have broken or slipped off. You'll need t open it up to see why the shaft from the motor will not spin or you will burn out the motor with the power on trying to make it go. It might be a DIY job if you can see an obvious problem like a slipped gear, otherwise take it to a repair specialist.

Posted on Apr 30, 2009

QuietRiot

  • 145 Answers

SOURCE: i have a kitchen aid stand mixer and the head

This sounds like an issue of beater to bowl adjustment, which can come out of alignment naturally over time and with use of the machine.

If the flat beater is striking the bottom of your bowl, this may cause the locking mechanism to loosen and may cause the mixing head to "bounce" during use.

Your Use and Care Guide will cover the "beater to bowl adjustment," which you can do at home in a few minutes with a flathead screwdriver.

Posted on Jul 08, 2009

Anonymous

  • 398 Answers

SOURCE: My Kitchen Aid Artisan Stand Mixer only runs on high speed.

you can try to use some oil free contac cleaner on the speed switch. if that don't fix it put a new speed control switch in it.

Posted on Jul 20, 2009

Anonymous

  • 55 Answers

SOURCE: My Kitchen Adie stand mixer has a Smell of burnt

Please don't buy a new one, Its easier to send to us USPS which is very inexpensive plus you get a 1yr warranty and it's fast service and the best satisfaction you will ever experience

estimated cost $39-$49.99

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is this a Kitchen Aid? Is it possible to buy this circuit board from somewhere?


This is a kitchen aid. BUT!!!! it is an international model that was sold in countries with 220 volts. Look underneath the mixer for a white tag it should have a model number and a serial number, if you can get us those numbers then we can help with the parts. Hope this helps.

Nov 05, 2014 | Food Mixers

1 Answer

Kitchen aid mixer only goes 1 speed


The number in your question (9706529) is for the worm gear.
What is the model Kitchenaid mixer you have?

Jul 21, 2014 | KitchenAid 9706529 Stand Mixer Worm Gear...

1 Answer

Kitchen aid hd professional mixer problems with speed controls


you need a new speed control board, easy fix about $35.00 for the part and an hour of your time, not even messy to do a total of six screws and four wire connections that clip on, several youtube step by step instruction videos available. parts available on ebay. let us know if this helps you

Jan 28, 2013 | KitchenAid Food Mixers

1 Answer

My kitchenaid mixer run on high at all times


If your mixer only runs on high speed there are 3 things that can cause that. The first thing to check will be the speed control plate, Remove the trim and end cover on the mixer, the first thing you should see is the speed control plate, this has 3 screws on it, try adjusting the top two screws 1/4 turn, this should slow the mixer down, do not over tighten. Also check to see if the control plate spring is unhooked. If the spring is unhooked, attach to bottom of the control plate, and squeeze the spring end.
If this does not fix your mixer, check the wiring of the mixer, you can locate a wiring diagram on the last page of the service manual.
If the speed control plate is adjusted correctly and all the wiring is correct it will be your speed control phase board. You can test the speed control phase board to see if it is shorted. With the line cord disconnected, pull the t-b ar contacts to open, and insert a piece of paper between them so they cannot close. Reapply power-the mixer should just run or buzz trying to run. If it operates at full speed, teh phase control board is defective and needs to be replaced.
Here is a link to the service manual: http://lib.store.yahoo.net/lib/mendingshed/kitchenaidservicemanual.pdf
This will aid you in taking the mixer apart, troubleshooting and putting it back together, remember the wiring diagram is the very last page.
Thank you,
Colleen
Customer Service
MendingShed.com
800-339-9297

Jan 07, 2013 | KitchenAid K5SS Mixer Speed Control Plate...

1 Answer

Who repairs kitchen aid mixers


Call the Kitchen Aid small appliance warranty office and they will tell you where the authorized repair person is that is close to you.

Dec 16, 2012 | KitchenAid K45SS Classic Stand Mixer

1 Answer

My Kitchen Aid ksm150ps stand mixer mixes only at high speed even on the first setting. What could be the problem?


sounds like the set screw in the back unit is too tight. Take off the back cover with the single screw up top. On the switch assembly that is now revealed, run the switch back and forth to see how it is interacting. The small set screw at the bottom probably needs loosened or tightened to give you the other speeds.

Oct 31, 2011 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Oil leaking. Called KitchenAid, they said this was normal, and to run the mixer with paddle on at a speed of 10 for 2-3 minutes. She also said that the oil was not toxic! I think the high speed running...


Kitchen Aid is 100% correct. The cause of the problem is age and lack of regular use, the oils in the gearbox grease separate from the solids over time and the oil then leaks out at the planetary and sometimes where the 2 case halves join under the silver trim band.
If you are up for a small job knock the chrome trim ring around the planetary off and clean it out and wipe around the area it covers. It is called a drip ring for good reason, you may find it full of oil.
The grease Kitchen Aid used in their mixers is Food Grade and it's harmless.

Oct 30, 2017 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

My Kitchen Aid Artisan Stand Mixer only runs on high speed.


you can try to use some oil free contac cleaner on the speed switch. if that don't fix it put a new speed control switch in it.

Jul 20, 2009 | KitchenAid K45SS Classic Stand Mixer

1 Answer

Kitchen aid KSM90


If you can unplug the mixer and test resistance between leads of the selector switch. The resistance should vary from high to low as you move the selector from low to high. If cord and all else looks good and switch is bad replace the switch.

Mar 23, 2008 | KitchenAid KSM90 Ultra Power Series Stand...

Not finding what you are looking for?
KitchenAid Artisan Series Tilt-Head Stand Mixer Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

162 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...