Question about Weiser Lock POWERBOLT ELEC DEADBOLT

Open Question

The alarm keeps going off on my weiser powerbolt lock

Changed the batteries and reset the code but no difference.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 68 Answers

SOURCE: center button unlocks insted of locks code locks insted of unlock

Take off the inside cover and move the door direction jumper over one pin.

Posted on Mar 23, 2009

Ad
  • 26 Answers

SOURCE: my powerbolt keeps beeping short beeps and then

dead batteries

Posted on Aug 18, 2009

sonicboomele
  • 1557 Answers

SOURCE: How do I reprogram the

  • Remove the inner cover plate from the lock.
  • Locate the small round reset button near the left side of the circuit board (Red or Black).
  • To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.
  • To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.
best of luck.

Posted on Aug 02, 2010

  • 1 Answer

SOURCE: Changed the batteries but the Weiser keypad lock

Mine did that too for a month. Make sure all the batteries are new alkaline batteries of the same brand, and remove them for a few minutes (if already installed) and replace them in the unit. I reset my code as well afterword. Did the trick for me.

Posted on Oct 06, 2010

  • 963 Answers

SOURCE: Touch pad does not work on weiser lock powerbolt.

I found this Frequently Asked Questions sheet for the Powerbolt 1000:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

I hope this helps.

Posted on Mar 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I hve had the lock for 10 years & now the bolt will not engage or disengage when codes are entered. Gear spins but bolt does not react.


Weiser has a one year warranty against electronic malfunction and a lifetime warranty against mechanical and finish problems. Yours sounds like a mechanical problem.

You can review their warranty and contact them for further assistance from this link:

http://www.weiserlock.com/CustomerService/WarrantyInfo/Powerbolt.aspx

Good luck!

Jul 24, 2012 | Weiser Lock Powerbolt 1000 Lock

1 Answer

My Weiser powerbolt lock is beeping-changed batteries-won't stop


Why is my Powerbolt 1000 unit beeping?
To determine why your lock is beeping abnormally, please follow these steps:
  1. Take out batteries and unplug powerstrip.
  2. Let it sit for 1 minute, then put the batteries back in and wait another minute.
  3. If it does not beep, the keypad needs to be replaced (17733-1).
  4. If the unit continues to beep, the powerboard needs to be replaced (A17734-3,3 Powerboard 1470 brass finish; A17734-3,26D Powerboard 1470 satin chrome finish; A17734-3,5 Powerboard 1470 antique brass finish).
Contact Customer service from here:
http://www.weiserlock.com/CustomerService/ProductSupport/SupportContact.aspx

Good luck!

Jan 09, 2012 | Weiser Lock Powerbolt 1000 Lock

1 Answer

I need to reset the code


How do I change the access code (and delete my old code) on my Powerbolt 1000?
The steps below are to change your access code to a new code. This will also remove any previous codes stored in the Powerbolt's memory.

pb1000programbutton.jpg

  1. Manually put the bolt in the extended (lock) position. Press the PROGRAM button once, enter your new 4 - 8 digit code and then press the LOCK button.
  2. Press the PROGRAM button twice, enter the same new code and then press the LOCK button once.
  3. Press the PROGRAM button three times, enter the same new code and then press LOCK once.
If your old code still remains in the unit, you will need to perform a hard reset of the unit. To perform a hard reset of the unit, remove all four batteries and leave them out for 1 hour. After the hour has passed, you may re-enter the batteries.

Jun 22, 2011 | Weiser Lock GED1460X3BR Lifetime Polished...

1 Answer

The old code continues to work even when I program in a new code. How do I keep that from happening?


Have you changed the batteries recently? If you have and the problem still exists, there is a reset code in the manual. Also, keep in mind that these locks hold two separate codes in them, when changing codes, make sure you change both of them. You acn find a copy of the manual here: http://www.smarthomeusa.com/Products/ED1460XXXX/manuals/WeiserLockPowerbolt1000-manual.pdf

Mar 05, 2011 | Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

How do you reset all the codes on a weiser lock?


Here's a link to the Frequently Asked Questions page for the Powerbolt 1000:

http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx

The instructions for reprogramming the code can be found there. Good luck!!

Oct 29, 2010 | Weiser Lock Powerbolt 1000 Lock

1 Answer

We changed the batteries and the lock will not reset it will not lock or unlock just keeps bepping


check that the keypad is not defective. You can disconnect the batteries and then unplug the keypad. Now put the batteries in without the keypad connected. If the beeping stopped, your keypad may need replacing. http://www.weiserlock.com/en/SupportPortal/SuggestedFaqs.aspx?prod=FAQ+Categories_Keyless+Entry_Power+Bolt+1000

Oct 04, 2010 | Weiser Lock Powerbolt 1000 Lock

1 Answer

Changed the batteries but the Weiser keypad lock keeps beeping


Mine did that too for a month. Make sure all the batteries are new alkaline batteries of the same brand, and remove them for a few minutes (if already installed) and replace them in the unit. I reset my code as well afterword. Did the trick for me.

Aug 23, 2010 | Weiser Lock POWERBOLT ELEC DEADBOLT

1 Answer

Changed battery and lost program cant find manual need reprogram 4 number code


changed the battery and lost the manual, put my code in and it worked , latter it started to beep and now it doesn't work... respond at all ....help thanks

Apr 19, 2010 | Weiser Lock POWERBOLT ELEC DEADBOLT

Not finding what you are looking for?
Weiser Lock POWERBOLT ELEC DEADBOLT Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Azam Ali

Level 1 Expert

31 Answers

Scoee Scoffer

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

6032 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...