Question about Denon AVR-E400

Open Question

Denon avr e400 red blinking light. Turns on and shuts off and starts a red blinking. What can I do?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
simplemitch
  • 752 Answers

SOURCE: Denon AVR-4800 5.1Channel Standby light blinking

It's going into protect. Unhook ALL the speakers and see if it still shuts itself off. If so, then it will have to be taken in for service.

Posted on Oct 27, 2007

Ad
  • 54 Answers

SOURCE: Denon AVR-1601

This is a very common problem with denon receivers of the 2001-2-3 vintage. On almost every one, there are 4 little "surge" resistors in the power supply. These werent quite robust enough from the factory and one day would just burn open for no reason. Well, actually there is a reason, the "surge" that happens every time you power the unit up eventually weakens the resistors and then they pop. You need to take this to a denon service shop as I GUARANTEE they have seen this before. They need to check resistors in the picture, locarde above the **** rectangular connector. Resistors numbers R141, 142, 148, 149: 75f69d7.jpg These resistors when measured, should be less than 10 ohms each. If they are more, then they are blown. If they are blown, then have the shop check the channels for blown output transistors. If the outputs are OK, then these resistors should be replaced with 1 ohm 1/2 watt metal -film flameproof resistors. You might need to be prepared for a large bill, because the entire unit must come apart to replace the resistors, however, just checking them takes only about 10 minutes... Good luck and don't try this at home. Rob

Posted on Apr 08, 2008

  • 624 Answers

SOURCE: Denon AVR-1907 blinking red power button

It sounds like you have a bad speaker on the zone 2, or you have the speakers connected improperly.

When you engage the zone 2 a relay clicks and the speakers then become part of the amplifiers circuit.

If the problem was in the amplifier, it would go into protect mode without even having speakers connected to it.

If the speakers all check good, you most likely have the wrong type of speakers, meaning the impeadance is too low, or you have too many speakers connected to it.

On the back of the Denon, you will see right around the speaker output jacks, what ratings the speakers should be. If I remember correctly, it says 6 ohms or more when using only "A" or "B", and it says 12ohms or more for "A" + "B".

If you have two 8 ohm speakers on the same speaker jack you now have a 4 ohm load. That is below the ratings and can cause the amp to shut down (go into protect). Since your amp shuts down right away, I think you have a bad speaker or way too many speakers connected.

I have seen many times when people will connect 2 or 4 speakers to the one of the outputs that are designed for only 1 speakers.

If you are using too many speakers you will need a speaker distribution box. It has a resistor network built into it so the amp never sees a lower impeadance than what it is designed for.
You can connect 4, 6 or 8 speakers to one set of outputs designed for 2 speakers. You do loose a lot of power to the speakers, but it is better than blowing up your amplifier.

If I can be of any further help, let me know.

Posted on Jun 22, 2008

localwonder
  • 6784 Answers

SOURCE: shuts off then red light indicator flashes, disconnected all speakers but still wont work

Hi, this is a power board issue. remove the cover and make sure that this unit doesn't have blow fuse. if the fuse is fine, you will then need to replace the integrated power/ main board.

Posted on May 21, 2009

SOURCE: Denon avr-1804 its turns back after 5 sec

Disconnect all speaker wires on back and then turn on. If it happens again, it's most likely a power supply problem. If it doesn't happen again, it was probably crossed speaker wires.

Posted on Dec 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to connect a denon avr-e400 receiver to a televion


If the DENON has an HDMI output, and your TV has an HDMI input, then use a HDMI cable. Then, use the TV's remote-control to select "source" (or "input") as 'HDMI 2' or 'HDMI 3' (assuming that you have been using 'HDMI 1' to watch TV).

Feb 08, 2015 | Denon AVR-E400 7.1 Channel 4K and 3D Pass...

1 Answer

Denon AVR-1312 turns on displays for a second switches off and the red light starts to flash


you most likely have a shortedchannel in the amp that would need to be repaired

Jul 31, 2014 | Denon AVR1312 51 Channels Receiver

1 Answer

Denon avr-1513 shutting off and blinking red light


Sounds like you could have a bad speaker connection. Try disconnecting the speakers and see if it stays on. If so, connect one at at a time until it goes off to determine which one.

Jan 20, 2013 | Denon 5.1 Channel Receiver 1080p AVR-1513

1 Answer

Only red light is blinking on my denon avr 1508


It sounds like you overloaded the Denon avr with too much resistence from the speakers. Please check the total resistence of the speakers before you connect them all. Also check that the speakers or their wires are not shorted!

Jan 20, 2013 | Denon Audio Players & Recorders

1 Answer

Red power light blinking on my denon avr 1907, tried reset procedure, no speakers hooked up now and it still goes from green light to blinking red light and shuts off...Any clues?


This is a protection mode. The receiver protection circuit detects an internal problem like missing power supply voltage or blown channel and shuts down the receiver. You need to bring the unit to a repair facility.

Sep 26, 2011 | Denon AVR-1907 Receiver

1 Answer

Denon AVR-1906 Reciever is not working. Was watching a movie and then it suddenly shut off. Now, the power light is blinking red. When I try to power it on again it starts to boot up but then turns off...


speaker terminal are short circuit,switch power off connect speaker properly then switch power back.
-the ventilation holes of the set are blocked-turn power off and make good ventilation around leave the set to cool and turn power back.
-the unit is operating at continuous high power turn it of and allow for cool down and switch it back.

Jun 01, 2008 | Denon Audio Players & Recorders

2 Answers

Denon AVR-4800 5.1Channel Standby light blinking


It's going into protect. Unhook ALL the speakers and see if it still shuts itself off. If so, then it will have to be taken in for service.

Oct 27, 2007 | Denon AVR-4800 Receiver

Not finding what you are looking for?
Denon AVR-E400 Logo

Related Topics:

794 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...