Question about HP LaserJet 3600n Printer

1 Answer

Unit says install fuser - HP LaserJet 3600n Printer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • HP Expert
  • 147 Answers
  • douggt
    douggt Dec 18, 2015

    Link is broken just redirects to main page.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code e1 showing at xerox pro 420? solution..


rror codes If the printer's front panel displays a message Error XX, find the error code in this table and follow the instructions for resolving the problem. If problems persist, check the Xerox web site www2.tek.com/TekSMART/ or contact service.
Error User Corrective Action Error 01
  • Remove and re-install the black Toner Cartridge, then turn the printer off and on.
  • Replace the black Toner Cartridge, then turn the printer off and on.
Error 02
  • Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.
  • Replace the cyan Toner Cartridge, then turn the printer off and on.
Error 03
  • Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.
  • Replace the magenta Toner Cartridge, then turn the printer off and on.
Error 04
  • Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.
  • Replace the yellow Toner Cartridge, then turn the printer off and on.
Error 05, 10, 11,12, and 13
  • Turn the printer power off, then on.
Error 20
  • Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Remove and re-install the Main Charge Grid. Turn the printer off, then on.
  • Remove and re-install the Transfer Kit. Turn the printer off, then on.
  • Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.
  • Replace the Main Charge Grid. Turn the printer off, then on.
  • Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Replace the Transfer Kit. Turn the printer off, then on.
  • Replace the Toner Cartridges. Turn the printer off, then on.
Error 21, 22, 30,and 32
  • Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • If a problem persists for Error 30, clean the sensor. See Cleaning Phaser 750 Printers.
Error 33
  • Check for jammed paper throughout the paper path (especially in paper feeder).
  • Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.
Error 40, 41, 42,and 43
  • Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.
  • Make sure that you have the correct Fuser for your local printer power supply:
    110-Volt Fuser Part Number 016-1839-00
    220-Volt Fuser Part Number 016-1840-00
  • Replace the Fuser. Turn the printer off, then on.
Error 50, 51
  • Turn the printer off, then on.
Error 52
  • Remove the Duplex Unit (if installed).
  • Check for paper under the Upper Tray.
  • Turn power off, then on.
Error 53
  • Open left door and remove any jammed media.
  • Tun the printer off, then on.
Error 60
  • Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.
  • Reinstall the media. Make sure you do not overfill the tray.
Error 61
  • Remove and re-install each Toner Cartridge. Turn the printer off, then on.
  • Replace each Toner Cartridge. Turn the printer off, then on.
Error 62
  • Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).
  • Remove and re-install the Fuser. Turn the printer off, then on.
  • Slide out and re-insert the paper feeder. Turn the printer off, then on.
  • Replace the Fuser. Turn the printer off, then on.
Error 63
  • Remove and re-install the Imaging Unit. Turn the printer off, then on.
  • Replace the Imaging Unit. Turn the printer off, then on.
Error 70, 71, and72
  • Turn the printer off, then on.
Error 73
  • Remove and re-install the Imaging Unit. Turn the printer off, then on.
  • Replace the Imaging Unit. Turn the printer off, then on.
Error 74
  • Remove and re-install the Fuser. Turn the printer off, then on.
  • Replace the Fuser. Turn the printer off, then on.
Error 80, 81, 82,83, and 84
  • Make sure that all four toner cartridges are installed in the printer.
  • Turn the printer off, then on.
Error 01p through
Error 47p
  • Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).
  • you can helpful

Oct 09, 2014 | Xerox Phaser Office Equipment & Supplies

1 Answer

Hello, I replaced the fuser on my 734de and I still get fuser life warning


Did you replace the fuser with a new Lexmark fuser or a refurbished unit? The original Lexmark units have a chip in them that resets the counter when installed. However this only works the first time the fuser is installed. If you install a used fuser in a different printer it will not reset the counter.

Sep 30, 2014 | Lexmark Office Equipment & Supplies

1 Answer

CP5225N WRONG FUSER INSTALLED ERROR


Was the replacement fuser 'new' or 'refurbished'? Try re-installing the fuser, that will usually correct the problem. If not, contact your vendor & see if they will exchange it. Always try to replace parts with Factory New. I don't work for or represent any brand, but in always tell my customers: Buy new Factory parts.

Mar 20, 2014 | HEWLETT-PACKARD Color LaserJet CP5225...

1 Answer

Xerox 4150 workcenter says fuser module needs to warm up. This appears usually first thing in morning. I have to power off then on to stop this from showing on the screen. also, it wont print until after I...


1. Switch off the machine, then switch on the machine.
2. Enter dC330 code 10-100 to heat the fuser to 180 degrees. Enter codes 10-200 (centre
thermistor) and 10-210 (front thermistor) to verify the condition of the thermistors.
3. Enter code 10-300 to check power supply unit 2. If necessary, install a new power supply
unit 2, PL 1.10 Item 4.
4. Switch off the machine. Remove the fuser assembly. Check that the thermistors, PL 10.25
Item 9 are clean and in good contact with the fuser heat roller. Check the wiring to the
thermistors. Install new components as necessary, PL 10.25.
5. Check for continuity between the two pins on the fuser assembly connector, PL 10.25
Item 8.
NOTE: A cold fuser has a resistance of approximately 11.5 ohms (220V/240V) or 2 ohms
(110V).
6. Check that there is continuity through the fuser heater and across the over temperature
cut-out.
7. Check the wiring between the fuser connector, PL 4.15 Item 20 and CON3, CON8 and
CON9 on Power Supply Unit 2. If necessary, install a new fuser connector, PL 4.15 Item
20.
8. Check the wiring between CON4 on Power Supply Unit 2 and CN7 on the Main PWB.
9. Install new components as necessary:
• Fuser assembly, PL 10.25 Item 1.
• HVPS, PL 1.10 Item 2.
10. Perform the OF5 Main PWB Check RAP.
4250/4260 Checkout
NOTE: The main PWB has test points. The location of the test points is shown on the Main
PWB PJ location illustration.
Refer to Wiring Diagram 17, Wiring Diagram 18 and Wiring Diagram 21. Perform the following:
1. Switch off the machine, then switch on the machine.
2. Enter dC330 code 10-100 to heat the fuser to 180 degrees. Enter codes 10-200 (centre
thermistor) and 10-210 (front thermistor) to verify the condition of the thermistors.
3. Enter code 10-300 to check power supply unit 2. If necessary, install a new power supply
unit 2, PL 1.15 Item 4.
4. Switch off the machine. Remove the fuser assembly. Check that the thermistors, PL 10.28
Item 9 are clean and in good contact with the fuser heat roller. Check the wiring to the
thermistor assembly. Check the wiring to the NC thermistor, PL 10.28 Item 19. Install new
components as necessary, PL 10.28.
5. Check for continuity between the three pins on the fuser assembly connector, PL 10.28
Item 8.
NOTE: A cold fuser has a resistance of approximately 11.5 ohms (220V/240V) or 2 ohms
(110V).
6. Check that there is continuity through the fuser heat lamps and across the over temperature
cut-out. Install new components as necessary, PL 10.28.
7. Check the wiring between the fuser connector, PL 4.15 Item 20 and CN5 on the Main
PWB. If necessary, install a new fuser connector, PL 4.15 Item 20.
8. Check the wiring between CON1 on Power Supply Unit 2 and CN7 on the Main PWB.
9. Install new components as necessary:
• Fuser assembly, PL 10.28 Item 1.
• Power supply unit 2, PL 1.15 Item 4.
10. Perform the OF5 Main PWB Check RAP

May 10, 2012 | Xerox WorkCenter 4150 Black and White...

1 Answer

My printer will not work it gives me system error 000


Hello,
To resolve the issue, please try reseating the fixing assembly. To do so, please follow the instructions below:
1) Unplug the power cord from the wall outlet.
Caution: The fuser unit and surrounding area can become extremely hot during operation. Perform the following procedure after the fuser unit has cooled down completely. Touching the fuser unit when it is still hot may result in burns. skumar_sreen_0.gif

2) Turn the lock release levers located on the back of the machine in the direction of the arrow and release the lock. skumar_sreen_1.gif

3) Hold the grip on the fuser unit and remove it. skumar_sreen_2.gif

Caution: The fuser unit weighs approximately 3.3 lb (1.5 kg), and it is heavier on the back side. Be sure to hold the grip securely when carrying a fuser unit. Dropping the unit may result in personal injuries. skumar_sreen_3.gif

4) Hold the grip on the fuser unit and install it securely. skumar_sreen_4.gif

5) Lock the fuser unit by turning the two lock release levers in the direction of the arrow. skumar_sreen_5.gif

6) Connect the power cord and all interface cables.
7) Plug the power cord in the wall outlet to turn on the machine.

Aug 30, 2011 | Laser Canon imageCLASS 8180C Multifunction...

1 Answer

010-327


010-327 Fuser On Time Failure RAP

• After the Main Lamp turned On during warm up, the Control Thermistor did not detect
READY temperature within the specified time.
• After the Main Lamp turned On during standby, the Control Thermistor did not detect a
specific temperature within the specified time.
• After the Sub Lamp turned On during standby, the Control Thermistor did not detect a
specific temperature within the specified time.
• After the empty rotation started, the Control Thermistor did not detect the empty rotation
finishing temperature within the specified time.
• After the Main Lamp turned On during printing, the Control Thermistor did not detect a
specific temperature within the specified time.
• After the Sub Lamp turned On during printing, the Control Thermistor did not detect a specific
temperature within the specified time.


Initial Actions
Check for paper on the Fuser. The Fuser has no paper wrapped round it.
No)Remove the paper.
Yes)Check the installation of the Fuser Unit. The Fuser Unit is securely installed.
No)Install the Fuser Unit securely.
Yes)Remove the Fuser Unit. Check the conductivity of the contact points of the Thermostat. The
contact points are connected.
No)Replace the Fuser Unit
Yes)Check the resistance of the Main Lamp between P600-3 and P600-7 for an open circuit or a
short circuit . The resistance of the Main Lamp is 100 ohms or lower.
No)Replace the Fuser Unit
Yes)Check the resistance of the Sub Lamp between P600-1 and P600-7 for an open circuit or a
short circuit . The resistance of the Sub Lamp is 100 ohms or lower.
No)Replace the Fuser Unit
Yes)Check the resistance of the Control (Center) Thermistor between P600-5 and P600-6 . The resistance is 3k ohms or higher.
No)Replace the Fuser Unit
Yes)Check the resistance of the Rear Thermistor between P600-2 and P600-4 . The resistance is 3k ohms or higher.
No)Replace the Fuser Unit
Yes)Check the wire between J410 and J600 for an open circuit or a short circuit . The wire between J410 and J600 conducts with less than a few ohms.
No)Repair the open circuit or short circuit.
Yes)Check the wire between J6 and J600 for an open circuit or a short circuit . The wire between J6 and J600 conducts with less than a few ohms.
No)Repair the open circuit or short circuit.
Yes)Check the wire between J401 and J523 for an open circuit or a short circuit .The wire between J401 and J523 conducts with less than a few ohms.
No)Repair the open circuit or short circuit.
Yes)Replace the Fuser Unit . If the problem persists, replace the Power Unit . If the problem persists, replace the MCU PWB .

END

Aug 03, 2011 | Xerox WorkCentre PRO 128 Copier

1 Answer

Error 010-297 restart printer


Hi belljohnson5,

The code is caused by a small switch under the fuser unit not sensing the fuser unit is in place. The blue plastic locking tab on the left side of the fuser has a small catch on the bottom of the fuser. The catch is supposed to slip thru a space in the steel plate under the fuser unit and secure the fuser in place. As the catch slides forward under the steel plate, it pushes on the trigger of the sensing switch, closing the sensing switch and letting the copier know that the fuser is in place. (there is also a similar locking tab on the right of the fuser but it doesn't trigger a sensor like the left one does) 1) The fuser gets very Hot!! Let cool for 10 minutes after turning off the power and unplugging the copier! 2) Pull the two blue locking tabs forward and remove the fuser unit. Reinsert and push back on the tabs to lock back into place. Sometimes just reinserting the fuser will allow the catch on the locking tab to function correctly and push the trigger on the sensing unit. Turn the copier back on and pray the error code doesn't reappear.. 3) Mine reappeared. Evidently the catch on the fuser unit was still not pushing the trigger forward, causing the copier to surmise that no fuser unit was installed. At this point, you should buy another fuser unit or take your copier to an authorized Dell repair center.

Hope this helps.

Thank you for using FixYa.

May 05, 2010 | Dell 3100cn Laser Printer

1 Answer

Copycentre c20 has open heat error message. How do I replace fuser unit?


The fuser unit for this machine can only be installed by a technician as the fuser unit itself is not for sale to consumers.

Nov 19, 2009 | Xerox CopyCentre C20 Black and White...

4 Answers

Put in newer fuser unit but machine still says to replace


If you want to clear the fuser message you have to be sure you replaced the fuser web. Then go to 25 => counter clear(items 13)=> Clear fuser counter or 36=>counter clear(items 8)=>Clear fuser counter.

May 28, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

E002 error


Hi,

First of all to troubleshoot this problem, please reseat the fixing assembly. To do this, please follow the steps below:

Reseating the Fixing Assembly
  1. Unplug the power cord from the wall outlet.
    unplug_power_cord.gif

    caution.gif
    The fuser unit and surrounding area can become extremely hot during operation. Perform the following procedure after the fuser unit has cooled down completely. Touching the fuser unit when it is still hot may result in burns.
    caution_fuser_unit.gif


  2. Turn the lock release levers located on the back of the machine in the direction of the arrow and release the lock.
    turn_locking_release_levers_on_back.gif


  3. Hold the grip on the fuser unit and remove it.
    hold_grip_on_fuser_unit_and_remove_it.gif

    caution.gif
    The fuser unit weighs approximately 3.3 lb (1.5 kg), and it is heavier on the back side. Be sure to hold the grip securely when carrying a fuser unit. Dropping the unit may result in personal injuries.
    fuser_unit_weighs_3_lbs.gif


  4. Hold the grip on the fuser unit and install it securely.
    install_fuser_unit_securely.gif


  5. Lock the fuser unit by turning the two lock release levers in the direction of the arrow.
    lock_fuser_unit_by_turning_lock_release_levers.gif


  6. Connect the power cord and all interface cables.


  7. Plug the power cord in the wall outlet to turn on the machine.



Jan 15, 2009 | Canon imageCLASS MF8170C All-In-One Laser...

Not finding what you are looking for?
HP LaserJet 3600n Printer Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...