Question about KitchenAid 5-speed Blender With Glass Blender Jar Ksb565er
Glass jar is leaking at base
Posted by Anonymous on
It will either be the rubber gasket (it goes between the glass jar and the blade assy) or it could be a worn bearing/bush around the chopping blade shaft. Replace either the gasket or the blade assy.
Posted on Jul 23, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
your blade assembly is corroded. take it off, and using a rag, grab the blades. using another rag, grab the other end (probably rubber) and turn CLOCKWISE - it's threaded reverse, so you have to turn to the right to loosen, not the left like usual. I had to clean out the rod that connects to the blades - it was all nasty and corroded. I cleaned it with my Dremel and regreased with a tube of grease I keep in the garage, cleaned all other parts with some Dawn, dried well, reassembled, and works almost like new. I'm guessing I ran it too long without pulsing the motor and the heat corroded the rod that's connected to the blades. OR you can buy a replacement blade unit for about $10 online on a blender parts site
Posted on Jan 15, 2010
this is getting more and more common there is a part between the motor and the drive gear that snaps for no reason . its job is to snap if the blades jam as a "fuse" to save your house from a overheating ,jammed motor . the problem is there are no parts to buy to fix this . if its new take it back to where you bought it . otherwise shipping it 2 ways for repair to the factory is sometimes as much or more as a new blender ........ i would recomend you do one of two things : go to a goodwill or other type shop and get a nice vintage blender , it will last forever ! or move up to a vita mix . its costly but it will realy last you ... this new made in china junk is just bad news even when it has the kitchen aid name on it . its still the same junk ..... good luck........ Please if this answer helped , please rate this 3 or 4 stars . and keep me in the paid answer department . A 1 or 2 may knock me down into the unpaid ranks. Thanks Cactus Bob .
Posted on Mar 24, 2009
They are usually in stock here:
Posted on Jan 24, 2010
SOURCE: We own a kitchen aide
The Instruction & Recipe booklet for the Kitchen Aid KSB550, KSB560, KSB570, KSB580 5-speed Blender can be found here:
There is no infomration to suggest that the blender blade could be removed for replacement of a seal
On page 27 of the pdf (page 24 if printed) there is contact information for ordering replacement parts. You might ask if the blade assemly can be ordered and replaced separtely but I believe you must replace trhe blender jar and blade unit as one piece.
Posted on Mar 18, 2011
Are you sure you are installing the gasket correctly?
Leaks are usually the result of a misaligned or cross-threaded blender jar base or from the gasket being installed incorrectly. Make sure the gasket is installed between the blade assembly and the screw on base.
If this does not help, please reply or repost.
Posted on Dec 09, 2012
Tips for a great answer:
Mar 07, 2014 | Oster 6700 Work Top Blender
Feb 20, 2014 | Braun MX2050 Blender Powermax Replacement...
May 29, 2013 | GE small appliance blenders 169169 User...
Feb 02, 2013 | Braun MX2050 Blender Powermax Replacement...
Dec 07, 2012 | KitchenAid 5-speed Blender With Glass...
May 19, 2012 | Blenders
Mar 15, 2011 | Juicelady JL600 Professional Work Top...
Sep 16, 2009 | Haier HB500 2-Speed Blender
Feb 09, 2009 | Kenmore KMB048 Work Top Blender
Jun 16, 2008 | Back to Basics Blender Solution 5500...
1,271 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: